Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
test-and-measurement:analog-discovery-studio:canvases:analog-discovery-canvas:getting-started-guide [2021/05/20 01:26] – [Inventory] Keith M Kolmos | test-and-measurement:analog-discovery-studio:canvases:analog-discovery-canvas:getting-started-guide [2022/09/12 15:50] (current) – changed forum.digilentinc.com to forum.digilent.com Jeffrey | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Analog Discovery Canvas | + | ====== Getting Started with the Analog Discovery Canvas |
{{: | {{: | ||
- | ==== Introduction ==== | + | ===== Introduction |
This guide explains the use of the Analog Discovery Canvas with the Analog Discovery Studio or the Analog Discovery 2. The Analog Discovery Canvas is used to host user designed circuitry and connects to the Analog Discovery Studio through the magnets beneath each of the four standoffs in the corners of the Analog Discovery Canvas. The Analog Discovery Canvas includes the following features: | This guide explains the use of the Analog Discovery Canvas with the Analog Discovery Studio or the Analog Discovery 2. The Analog Discovery Canvas is used to host user designed circuitry and connects to the Analog Discovery Studio through the magnets beneath each of the four standoffs in the corners of the Analog Discovery Canvas. The Analog Discovery Canvas includes the following features: | ||
Line 13: | Line 13: | ||
* 2x15 connector to make a connection with an Analog Discovery | * 2x15 connector to make a connection with an Analog Discovery | ||
* 2x10 connector to plug into the Analog Discovery Studio | * 2x10 connector to plug into the Analog Discovery Studio | ||
+ | * 4 power switches to turn on / off the power supplies | ||
+ | * 6 green LEDs for power supply indication | ||
+ | |||
+ | The following are only for use with the Analog Discovery 2 (not connected to the Analog Discovery Studio) | ||
* 2 wire harness to plug into Oscilloscope 1 | * 2 wire harness to plug into Oscilloscope 1 | ||
* 2 wire harness to plug into Oscilloscope 2 | * 2 wire harness to plug into Oscilloscope 2 | ||
* 2 wire harness to plug into Wavegen Out 1 | * 2 wire harness to plug into Wavegen Out 1 | ||
* 2 wire harness to plug into Wavegen Out 2 | * 2 wire harness to plug into Wavegen Out 2 | ||
- | * 4 Power switches to turn on / off the power supplies | ||
- | * 6 Green LEDs for Power Supply indication | ||
---- | ---- | ||
- | ==== Inventory ==== | + | ===== Inventory |
You will need a: | You will need a: | ||
Line 30: | Line 32: | ||
You will also need one of the following: | You will also need one of the following: | ||
- | * [[https://store.digilentinc.com/ | + | * [[https://digilent.com/shop/ |
- | * [[https://store.digilentinc.com/ | + | * [[https://digilent.com/shop/ |
---- | ---- | ||
- | ==== Demonstration Using an Analog Discovery | + | ===== Connecting the Analog Discovery |
- | In this first section, we will show you how to use the Analog Discovery Canvas with the Analog Discovery Studio. | + | In this first section, we will show you how to use the Analog Discovery Canvas with the Analog Discovery Studio |
- | ==== 1. Setup ==== | + | |
+ | --> Analog Discovery Studio | ||
<WRAP group> | <WRAP group> | ||
<WRAP column half> | <WRAP column half> | ||
- | == 1.1 == | ||
- | |||
The Analog Discovery Canvas attaches to the Analog Discovery Studio through four magnets beneath each of the four standoffs in the corners. | The Analog Discovery Canvas attaches to the Analog Discovery Studio through four magnets beneath each of the four standoffs in the corners. | ||
Line 55: | Line 56: | ||
<WRAP group> | <WRAP group> | ||
<WRAP column half> | <WRAP column half> | ||
- | == 1.2 == | ||
- | |||
Install the included cable between the 20 pin Analog Discovery Studio connector from the Canvas to the Analog Discovery Studio. | Install the included cable between the 20 pin Analog Discovery Studio connector from the Canvas to the Analog Discovery Studio. | ||
Line 80: | Line 79: | ||
</ | </ | ||
---- | ---- | ||
+ | <-- | ||
- | ==== Demonstration Using an Analog Discovery 2 ==== | + | --> |
- | + | ||
- | ==== 2. Setup ==== | + | |
<WRAP group> | <WRAP group> | ||
<WRAP column half> | <WRAP column half> | ||
- | == 2.1 == | ||
With the Analog Discovery 2 disconnected from your computer and the (optional) power supply turned off, connect it to the Analog Discovery Canvas via the 2x15 header found in the upper left hand corner of the Analog Discovery Canvas. | With the Analog Discovery 2 disconnected from your computer and the (optional) power supply turned off, connect it to the Analog Discovery Canvas via the 2x15 header found in the upper left hand corner of the Analog Discovery Canvas. | ||
Line 101: | Line 98: | ||
<WRAP group> | <WRAP group> | ||
<WRAP column half> | <WRAP column half> | ||
- | == 2.2 == | ||
Connect the Analog Discovery 2 to your computer via the USB cable and plug in the (optional) power supply. | Connect the Analog Discovery 2 to your computer via the USB cable and plug in the (optional) power supply. | ||
Line 108: | Line 104: | ||
<WRAP column half> | <WRAP column half> | ||
- | </ | + | {{:test-and-measurement: |
- | </ | + | |
- | ---- | + | |
- | + | ||
- | + | ||
- | ==== 3. Using the Analog Discovery Canvas ==== | + | |
- | <WRAP group> | + | |
- | <WRAP column half> | + | |
- | == 3.1 == | + | |
- | + | ||
- | The Breadboard Canvas has four different power supplies that are controlled by four power switches in the top right hand corner of the Canvas: +3.3V, +5.0, both ±12.0V, and both of the ± variable voltages. The variable voltage ranges operate between +1V to +5V for V+ and between | + | |
- | + | ||
- | <WRAP center round important 60%> | + | |
- | The Supplies instrument in the WaveForms software must be enabled for the variable voltages to work. | + | |
- | </ | + | |
- | + | ||
- | </ | + | |
- | <WRAP column half> | + | |
- | {{: | ||
</ | </ | ||
</ | </ | ||
---- | ---- | ||
+ | <-- | ||
- | ==== Next Steps ==== | + | ===== Next Steps ===== |
+ | Now that the canvas is connected to your device, you can begin using your device largely as you would before, access to Analog Discovery 2 pins are entirely provided through the canvas, while for the Analog Discovery Studio, you will still use the BNC probes or MTE cables for connection to the Oscilloscope and Wavegen instruments. | ||
- | For more guides on how to use the Analog Discovery Studio, return to the device' | + | For more guides on how to use your Test and Measurement device, return to its resource center: |
For more information on WaveForms, visit the [[software: | For more information on WaveForms, visit the [[software: | ||
- | For technical support, please visit the [[https:// | + | For technical support, please visit the [[https:// |
{{tag> | {{tag> |