Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
test-and-measurement:guides:waveforms-impedance-analyzer [2021/05/14 23:05] – ↷ Page moved from reference:test-and-measurement:guides:waveforms-impedance-analyzer to test-and-measurement:guides:waveforms-impedance-analyzer Arthur Brown | test-and-measurement:guides:waveforms-impedance-analyzer [2024/02/29 14:25] (current) – [Using the Impedance Analyzer] replaced image Fausto Soares | ||
---|---|---|---|
Line 3: | Line 3: | ||
~~TechArticle~~ | ~~TechArticle~~ | ||
- | {{reference:test-and-measurement:analog-discovery-studio: | + | {{test-and-measurement/analog-discovery-pro-2230/impedance-screenshot.png?nolink|}} |
===== Introduction ===== | ===== Introduction ===== | ||
Line 11: | Line 11: | ||
===== Prerequisites ===== | ===== Prerequisites ===== | ||
* Digilent Test and Measurement Device with Analog Inputs and Outputs: | * Digilent Test and Measurement Device with Analog Inputs and Outputs: | ||
+ | * [[test-and-measurement: | ||
+ | * [[test-and-measurement: | ||
* [[test-and-measurement: | * [[test-and-measurement: | ||
+ | * [[test-and-measurement: | ||
* [[test-and-measurement: | * [[test-and-measurement: | ||
* [[test-and-measurement: | * [[test-and-measurement: | ||
Line 17: | Line 20: | ||
* Computer with WaveForms Software Installed | * Computer with WaveForms Software Installed | ||
* A Reference Circuit, which can be provided by: | * A Reference Circuit, which can be provided by: | ||
- | * [[https://store.digilentinc.com/ | + | * [[https://digilent.com/shop/ |
+ | * [[https:// | ||
* A reference resistor appropriate for the specific load, as described in [[# | * A reference resistor appropriate for the specific load, as described in [[# | ||
Line 70: | Line 74: | ||
In this tutorial, the impedance of a 10nF capacitor is measured. Referring to the previous table, a 10kOhm reference resistor is required for this value of capacitance. Refer to the "Load First" diagram to the right for how to set up this circuit (the capacitor is the load and the reference resistor is the resistor in the diagram.) | In this tutorial, the impedance of a 10nF capacitor is measured. Referring to the previous table, a 10kOhm reference resistor is required for this value of capacitance. Refer to the "Load First" diagram to the right for how to set up this circuit (the capacitor is the load and the reference resistor is the resistor in the diagram.) | ||
- | **Note:** //The Analog Input channels can be used with BNC Cables. For more information, | + | **Note:** //The Analog Input channels can be used with BNC Cables. For more information, |
</ | </ | ||
<WRAP column half> | <WRAP column half> | ||
Line 83: | Line 87: | ||
* Ground (black wire) connected to the free end of the reference resistor | * Ground (black wire) connected to the free end of the reference resistor | ||
- | **Note:** //If desired, BNC Cables can be used to connect the Analog I/O channels to the circuit under test. This is discussed in detail in the [[reference:test-and-measurement: | + | **Note:** //If desired, BNC Cables can be used to connect the Analog I/O channels to the circuit under test. This is discussed in detail in the [[test-and-measurement: |
</ | </ | ||
{{ : | {{ : | ||
Line 95: | Line 99: | ||
---- | ---- | ||
- | The [[https://store.digilentinc.com/ | + | The [[https://digilent.com/shop/ |
--> Click here if using the Impedance Analyzer Adapter for Analog Discovery # | --> Click here if using the Impedance Analyzer Adapter for Analog Discovery # | ||
Line 106: | Line 110: | ||
---- | ---- | ||
<WRAP group> <WRAP column half> | <WRAP group> <WRAP column half> | ||
- | The Impedance Analyzer Adapter attaches to the MTE cable connector slot on the Analog Discovery | + | The Impedance Analyzer Adapter attaches to the MTE cable connector slot on the Analog Discovery. A load, whether a single component, or a circuit to test, should be connected to connector J2, and the component or jumpers should be locked in place with the orange clips. |
</ | </ | ||
{{ : | {{ : | ||
Line 424: | Line 428: | ||
===== Other Resources ===== | ===== Other Resources ===== | ||
- | For more guides on how to use the Digilent Test and Measurement device, return to the device' | + | For more guides on how to use the Digilent Test and Measurement device, return to the device' |
- | For more information on WaveForms, visit the [[reference:software: | + | For more information on WaveForms, visit the [[software: |
- | For technical support, please visit the [[https:// | + | For technical support, please visit the [[https:// |