Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
test-and-measurement:analog-discovery-pro-5250:reference-manual [2022/02/28 23:49] – Add Data Logger Arthur Brown | test-and-measurement:analog-discovery-pro-5250:reference-manual [2022/10/05 15:57] (current) – changed 'Scopes and Instruments' to 'Test and Measurement' Fausto Soares | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Analog Discovery Pro (ADP5250) Reference Manual ====== | ====== Analog Discovery Pro (ADP5250) Reference Manual ====== | ||
+ | |||
~~TechArticle~~ | ~~TechArticle~~ | ||
/*| image = {{ : | /*| image = {{ : | ||
Line 14: | Line 15: | ||
| image = {{: | | image = {{: | ||
| image = {{: | | image = {{: | ||
- | /* logger | + | | image = {{: |
| image = {{: | | image = {{: | ||
| image = {{: | | image = {{: | ||
Line 30: | Line 31: | ||
Since the Analog Discovery Pro’s analog input channels are shared, the Oscilloscope instrument cannot be used at the same time as the Spectrum Analyzer, Network Analyzer, or Impedance Analyzer instruments. | Since the Analog Discovery Pro’s analog input channels are shared, the Oscilloscope instrument cannot be used at the same time as the Spectrum Analyzer, Network Analyzer, or Impedance Analyzer instruments. | ||
+ | |||
+ | The Analog Discovery Pro features an additional connector, found just to the right of the analog input channels, that provides a square wave for use in compensating your probes. By connecting the probe to the tab indicated by the square wave symbol and the ground clip to the tab indicated by the ground symbol, a 5 V, 1 kHz, square wave reference signal can be measured using the Scope instrument. If your probes support adjusting the compensation, | ||
For more information on the analog input (" | For more information on the analog input (" | ||
Line 43: | Line 46: | ||
* Captured data files can be exported in standard formats | * Captured data files can be exported in standard formats | ||
* Scope configurations can be saved, exported, and imported | * Scope configurations can be saved, exported, and imported | ||
+ | * Front panel connector generating a 5 V, 1 kHz, square wave for convenient compensation of BNC oscilloscope probes | ||
---- | ---- | ||
Line 49: | Line 53: | ||
{{: | {{: | ||
- | The Analog Discovery Pro (ADP5250) can be used with WaveForms' | + | The Analog Discovery Pro (ADP5250) can be used with WaveForms' |
The waveform generator channel is considered a single ended pin, however, a connected circuit must share a ground with the Analog Discovery Pro. | The waveform generator channel is considered a single ended pin, however, a connected circuit must share a ground with the Analog Discovery Pro. | ||
Line 68: | Line 72: | ||
The Analog Discovery Pro (ADP5250) has 3 programmable Digital Voltage Supplies, which can supply between 0 V to +6 V, 0 V to +25 V, and 0 V to -25 V through the Power Supplies (" | The Analog Discovery Pro (ADP5250) has 3 programmable Digital Voltage Supplies, which can supply between 0 V to +6 V, 0 V to +25 V, and 0 V to -25 V through the Power Supplies (" | ||
- | For more information on using the programmable power supplies, please visit the [[test-and-measurement: | + | Each of the power supply rails is associated with an LED available on the connector, just above the supply' |
+ | |||
+ | For more information on using the programmable power supplies, please visit the [[test-and-measurement: | ||
==== Features ==== | ==== Features ==== | ||
Line 80: | Line 86: | ||
===== Data Logger ===== | ===== Data Logger ===== | ||
- | {{: | + | {{: |
- | The Analog Discovery Pro (ADP5250) can be used with WaveForms' | + | The Analog Discovery Pro (ADP5250) can be used with WaveForms' |
The Data Logger can capture buffers of data at update rates of up to 10 samples per second. The maximum duration of a log is dependent on the update rate, but at the extreme, can run for over a thousand hours. | The Data Logger can capture buffers of data at update rates of up to 10 samples per second. The maximum duration of a log is dependent on the update rate, but at the extreme, can run for over a thousand hours. | ||
Line 203: | Line 209: | ||
Each of WaveForms' | Each of WaveForms' | ||
- | A variety of code examples are available in the application to aid in learning to write WaveForms scripts. Additional resources for writing scripts can be found on the Scopes | + | A variety of code examples are available in the application to aid in learning to write WaveForms scripts. Additional resources for writing scripts can be found on the Test and Measurement |
A plot pane within the Script instrument itself can be used to integrate data from many different instruments, | A plot pane within the Script instrument itself can be used to integrate data from many different instruments, |