Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:analog-discovery-pro-5250:specifications [2022/02/19 00:41] – [Digital I/O] Arthur Browntest-and-measurement:analog-discovery-pro-5250:specifications [2023/12/18 19:55] (current) – James Colvin
Line 1: Line 1:
 ====== Analog Discovery Pro (ADP5250) Specifications ====== ====== Analog Discovery Pro (ADP5250) Specifications ======
 +/*
 +Additional material for ADP5470 and ADP5490.
 +https://www.ni.com/docs/en-US/bundle/vb-8034-specs/page/specs.html
 +https://www.ni.com/en-us/shop/model/vb-8034.html
 +
 +https://www.ni.com/docs/en-US/bundle/vb-8054-specs/page/specs.html
 +https://www.ni.com/en-us/shop/model/vb-8054.html
 +
 +PDFs of NI publicly published Specifications, GSGs, Calibration procedures, Visual Diagrams, and various Regulatory material have all been downloaded to James' computer Dec 18th 2023.
 +
 +*/
 +
 +
 ~~TechArticle~~ ~~TechArticle~~
 These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted. These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted.
Line 6: Line 19:
 ==== Analog Input Channels ==== ==== Analog Input Channels ====
  
-Supports the Oscilloscope, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments.+Supports the Oscilloscope, Data Logger, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments.
  
 === Vertical System === === Vertical System ===
Line 25: Line 38:
  
 |<100% 25%>| |<100% 25%>|
-^ Maximum Sampling Rate | 1 GS/s single channel, 500 MS/s per channel, dual channel ||+^ Maximum Sampling Rate | 1 GS/s single channel \\ 500 MS/s per channel, dual channel ||
 ^ Maximum Record Length | 1 MS per channel || ^ Maximum Record Length | 1 MS per channel ||
  
 ---- ----
 ==== Digital Channels / Logic Analyzer ==== ==== Digital Channels / Logic Analyzer ====
 +Supports the Logic Analyzer and Script Editor instruments.
  
 {{ :test-and-measurement:analog-discovery-pro-5250:connector.png?400 |}} {{ :test-and-measurement:analog-discovery-pro-5250:connector.png?400 |}}
Line 35: Line 49:
 === Vertical System === === Vertical System ===
 |<100% 40%>| |<100% 40%>|
-^ Number of Channels | 34 ||+^ Number of Channels | 34 [(At time of writing, WaveForms software does not support use of the CLK0/CLK1 lines. All 32 DIO pins are fully supported.)] ||
 ^ Maximum Input Frequency | 100 MHz || ^ Maximum Input Frequency | 100 MHz ||
 ^ Input Voltage | 0 V to 5 V || ^ Input Voltage | 0 V to 5 V ||
Line 45: Line 59:
  
 **Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. **Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation.
 +
 +~~REFNOTES~~
  
 === Horizontal System === === Horizontal System ===
Line 73: Line 89:
  
 |<100% 25% 25%>| |<100% 25% 25%>|
-^ Waveforms                                              || Sine, square, ramp / triangle, DC, arbitrary     | +^ Waveforms                                                               || Sine, square, ramp / triangle, DC, arbitrary  | 
-^ Update Rate                                            || 125 MS/s                                         | +^ Update Rate                                                             || 125 MS/s                                      | 
-^ Resolution                                             || 14 bits                                          | +^ Resolution                                                              || 14 bits                                       | 
-^ Number of Channels                                     || 1                                                | +^ Number of Channels                                                      || 1                                             | 
-^ Output Impedance                                       || 50 Ω                                             | +^ Output Impedance                                                        || 50 Ω                                          | 
-^ Sine    ^ Maximum Frequency                             | 20 MHz                                           | +^ Switchable Filter                                                       || 36 MHz lowpass, 7-pole, elliptical            | 
-^ :::     ^ Total Harmonic Distortion (1 MHz)             | -55 dBc                                          | +^ Sine                               ^ Maximum Frequency                   | 20 MHz                                        | 
-^ :::     ^ Total Harmonic Distortion (10 MHz)            | -50 dBc                                          | +| :::                                ^ Total Harmonic Distortion (1 MHz)   | -55 dBc                                       | 
-^ :::     ^ Spurious Free Dynamic Range (SFDR)            | -70 dB at 1 MHz (non-harmonic)                   | +| :::                                ^ Total Harmonic Distortion (10 MHz)  | -50 dBc                                       | 
-^ :::     ^ Phase Noise (1 MHz)                           | -115 dBc/Hz at 10 kHz offset                     | +| :::                                ^ Spurious Free Dynamic Range (SFDR)  | -70 dB at 1 MHz (non-harmonic)                | 
-^ Square  ^ Maximum Frequency                             | 5 MHz                                            | +| :::                                ^ Phase Noise (1 MHz)                 | -115 dBc/Hz at 10 kHz offset                  | 
-^ :::     ^ Rise / Fall Time                              | <20 ns (10% to 90%)                              | +^ Square                             ^ Maximum Frequency                   | 20 MHz                                        | 
-^ :::     ^ Overshoot                                     | <5%                                              | +| :::                                ^ Rise / Fall Time                    | <20 ns (10% to 90%)                           | 
-^ :::     ^ Jitter                                        | 8 ns cycle-to-cycle                              | +| :::                                ^ Overshoot                           | <5%                                           | 
-^ Ramp / Triangle Maximum Frequency                      || 1 MHz                                            | +| :::                                ^ Jitter                              | 8 ns cycle-to-cycle                           | 
-^ Accuracy (with >10 kΩ load)  ^ Amplitude (1 kHz sine)   | ±(1% of output value ±5 mV)                      | +^ Ramp / Triangle Maximum Frequency                                       || 20 MHz                                        | 
-^ :::                          ^ DC                       | ±(1% of output value ±7.5 mV)                    | +^ Accuracy (with >10 kΩ load)        ^ Amplitude (1 kHz sine)              | ±(1% of output value ±5 mV)                   | 
-^ Output Range                 ^ 50 Ω                     | ±6 V                                             | +| :::                                ^ DC                                  | ±(1% of output value ±7.5 mV)                 | 
-^ :::                          ^ Hi-Z (>10 kΩ)            | ±12 V                                            | +^ Output Range                       ^ 50 Ω                                | ±6 V                                          | 
-^ DC Offset                    ^ 50 Ω                     | ±6 V                                             | +| :::                                ^ Hi-Z (>10 kΩ)                       | ±12 V                                         | 
-^ :::                          ^ Hi-Z (>10 kΩ)            | ±12 V                                            | +^ DC Offset                          ^ 50 Ω                                | ±6 V                                          | 
-^ Frequency                    ^ Accuracy                 | ≤100 ppm                                         | +| :::                                ^ Hi-Z (>10 kΩ)                       | ±12 V                                         | 
-^ :::                          ^ Resolution               | 1 µHz                                            | +^ Frequency                          ^ Accuracy                            | ≤100 ppm                                      | 
-^ Arbitrary Waveforms          ^ Points                   | 1 MS                                             | +| :::                                ^ Resolution                          | 1 µHz                                         | 
-^ :::                          ^ Sample Rate              | 125 MS/s                                         | +^ Arbitrary Waveforms                ^ Points                              | 1 MS                                          | 
-^ Protection                                             || Short-circuit protected                          |+| :::                                ^ Sample Rate                         | 125 MS/s                                      | 
 +^ Protection                                                              || Short-circuit protected                       |
  
 **Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output. **Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output.
Line 318: Line 335:
 ---- ----
 ===== Power Requirements ===== ===== Power Requirements =====
-|<100% 25%> +|<100% 25%>| 
-  +^ Voltage Input Range | 100 V AC to 240 V AC, ±10%, 50/60 Hz ||
-^ Voltage Input Range | 100 V AC to 240 V AC, 50/60 Hz ||+
 ^ Power Consumption | 100 W maximum || ^ Power Consumption | 100 W maximum ||
 ^ Power Input Connector | IEC C13 power connector ||  ^ Power Input Connector | IEC C13 power connector || 
Line 343: Line 359:
  
 ==== DMM Isolation Voltages (Ground to Earth) ==== ==== DMM Isolation Voltages (Ground to Earth) ====
 +
 +<columns 100% 5% 95%>
 +{{:test-and-measurement:analog-discovery-pro-5250:hazard.png?40}}
 +<newcolumn>
 +**Hazardous Voltage:** This icon denotes a warning advising you to take precautions to avoid electrical shock.
 +</columns>
 +
 +=== Channel-to-earth Ground ===
 |<100% 25%>| |<100% 25%>|
 ^ Continuous | 300 V, Measurement Category II || ^ Continuous | 300 V, Measurement Category II ||
Line 350: Line 374:
  
 Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe. Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe.
 +
 +<columns 100% 5% 95%>
 +{{:test-and-measurement:analog-discovery-pro-5250:caution.png?40}}
 +<newcolumn>
 +**Caution:** Do not connect the ADP5250 hardware to signals or use for measurements within Measurement Categories III or IV.
 +</columns>
  
 ==== DC Power Supply Isolation Voltages ==== ==== DC Power Supply Isolation Voltages ====
 |<100% 25%>| |<100% 25%>|
-^ +25V and -25V to earth ground, continuous | 60VDC, Measurement Category 1 |||+^ +25V and -25V to earth ground, continuous | 60 VDC, Measurement Category 1 ||| 
 + 
 +**Note:** //Measurement Categories CAT I and CAT O (Other) are equivalent. The input circuits are not intended for direct connection to the MAINs building installations of Categories CAT II, CAT III, or CAT IV.//
  
 ---- ----
Line 377: Line 409:
  
 ---- ----
- +{{page>test-and-measurement:analog-discovery-pro-5250:certifications&fullpage&noindent}}
-==== Safety ==== +
-This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:  +
-  * IEC 61010-1, EN 61010-1  +
-  * UL 61010-1, CSA 61010-1 +
  
 ---- ----
- +All specifications provided courtesy of NI's documentation for the VB-8012: https://www.ni.com/docs/en-US/bundle/vb-8012-specs/resource/371527e.pdf.
-==== Electromagnetic Compatibility ==== +
- +
-This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use; for radio equipment; and for telecommunication terminal equipment:  +
-  * EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity   +
-  * EN 55011 (CISPR 11): Group 1, Class A emissions  +
-  * EN 55022 (CISPR 22): Class A emissions  +
-  * EN 55024 (CISPR 24): Immunity  +
-  * AS/NZS CISPR 11: Group 1, Class A emissions  +
-  * AS/NZS CISPR 22: Class A emissions  +
-  * FCC 47 CFR Part 15B: Class A emissions  +
-  * ICES-001: Class A emissions  +
- +
-**Note:** In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11) Class A equipment is intended for use only in heavy-industrial locations.  +
- +
-**Note:** Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.  +
- +
-**Note:** For EMC declarations and certifications, and additional +
- +
- +
----- +
- +
-====CE Compliance==== +
-This product meets the essential requirements of applicable European Directives, as follows:  +
-  * 2014/35/EU; Low-Voltage Directive (safety)  +
-  * 2014/30/EU; Electromagnetic Compatibility Directive (EMC)  +