Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
test-and-measurement:analog-discovery-pro-5250:specifications [2022/02/03 19:06] – Fix line breaks Arthur Brown | test-and-measurement:analog-discovery-pro-5250:specifications [2023/12/18 19:55] (current) – James Colvin | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Analog Discovery Pro ADP5250 Specifications ====== | + | ====== Analog Discovery Pro (ADP5250) Specifications ====== |
+ | /* | ||
+ | Additional material for ADP5470 and ADP5490. | ||
+ | https:// | ||
+ | https:// | ||
+ | |||
+ | https:// | ||
+ | https:// | ||
+ | |||
+ | PDFs of NI publicly published Specifications, | ||
+ | |||
+ | */ | ||
+ | |||
~~TechArticle~~ | ~~TechArticle~~ | ||
These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted. | These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted. | ||
Line 6: | Line 19: | ||
==== Analog Input Channels ==== | ==== Analog Input Channels ==== | ||
- | Supports the Oscilloscope, | + | Supports the Oscilloscope, Data Logger, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments. |
=== Vertical System === | === Vertical System === | ||
Line 14: | Line 27: | ||
^ Bandwidth (-3 dB) | 100 MHz || | ^ Bandwidth (-3 dB) | 100 MHz || | ||
^ Resolution | 8 bits || | ^ Resolution | 8 bits || | ||
- | ^ Accuracy | ± 2% of input ±1% full scale (V peak to peak) || | + | ^ Accuracy | ±2% of input ±1% full scale (V peak to peak) || |
- | ^ Input coupling | + | ^ Input Coupling |
^ Vertical Sensitivity (range) | 10 mV / div (100 mV peak to peak) \\ 20 mV / div (200 mV peak to peak) \\ 50 mV / div (400 mV peak to peak) \\ 100 mV / div (1 V peak to peak) \\ 200 mV / div (2 V peak to peak) \\ 500 mV / div (4 V peak to peak) \\ 1 V / div (10 V peak to peak) \\ 2 V / div (20 V peak to peak) \\ 5 V / div (40 V peak to peak)|| | ^ Vertical Sensitivity (range) | 10 mV / div (100 mV peak to peak) \\ 20 mV / div (200 mV peak to peak) \\ 50 mV / div (400 mV peak to peak) \\ 100 mV / div (1 V peak to peak) \\ 200 mV / div (2 V peak to peak) \\ 500 mV / div (4 V peak to peak) \\ 1 V / div (10 V peak to peak) \\ 2 V / div (20 V peak to peak) \\ 5 V / div (40 V peak to peak)|| | ||
- | ^ Input impedance | + | ^ Input Impedance |
- | ^ Acquisition | + | ^ Acquisition |
- | ^ DC Offset Range | 10 mV/div, 20 mV/div, 50 mV/ | + | ^ DC Offset Range | 10 mV/div, 20 mV/div, 50 mV/ |
---- | ---- | ||
=== Horizontal System === | === Horizontal System === | ||
- | |< | + | |< |
- | ^ Maximum | + | ^ Maximum |
- | ^ Maximum | + | ^ Maximum |
---- | ---- | ||
==== Digital Channels / Logic Analyzer ==== | ==== Digital Channels / Logic Analyzer ==== | ||
+ | Supports the Logic Analyzer and Script Editor instruments. | ||
{{ : | {{ : | ||
- | |||
- | |||
=== Vertical System === | === Vertical System === | ||
- | |<100% 40%> | + | |<100% 40%>| |
- | ^ Number of channels | + | ^ Number of Channels |
^ Maximum Input Frequency | 100 MHz || | ^ Maximum Input Frequency | 100 MHz || | ||
- | ^ Input voltage | + | ^ Input Voltage |
- | ^ Input current | + | ^ Input Current |
- | ^ Input threshold | + | ^ Input Threshold |
^ Threshold Accuracy | 350 mV || | ^ Threshold Accuracy | 350 mV || | ||
- | ^ Input Impedance | 100 kΩ \\ 7.5 pF pulled to -2.0V to +6.5V, varies with input threshold setting || | + | ^ Input Impedance | 100 kΩ ││ |
- | ^ Additional / Internal | + | ^ Additional / Internal |
**Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | **Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | ||
+ | |||
+ | ~~REFNOTES~~ | ||
=== Horizontal System === | === Horizontal System === | ||
- | |<100% 40%> | + | |<100% 40%>| |
- | + | ^ Timing | |
- | ^ Timing | + | ^ Maximum |
- | ^ Maximum | + | |
^ Record Length (Typical) | 1 MS || | ^ Record Length (Typical) | 1 MS || | ||
^ Record Length (Minimum) | 4 kS || | ^ Record Length (Minimum) | 4 kS || | ||
- | ^ Decimation | External Sample Clock, 1:1, 2:1, and n*4:1 where n is in an integer || | + | ^ Decimation | External Sample Clock, 1:1, 2:1, and n*4:1 where n is an integer || |
- | ^ Maximum Sample Compression | 2^15 to 1 || | + | ^ Maximum Sample Compression | 2<sup>15</ |
---- | ---- | ||
- | === Triggering === | + | ==== Triggering ==== |
- | + | |< | |
- | |< | + | ^ Trigger |
- | ^ Trigger | + | ^ Trigger |
- | ^ Trigger | + | ^ Trigger Types ^ Analog |
- | ^ Trigger Types | || | + | ^ ::: ^ Digital |
- | ^ | + | ^ Trigger Resolution ^ Analog / Oscilloscope |
- | ^ | + | ^ ::: ^ Digital / Logic Analyzer |
- | ^ Trigger Resolution | + | ^ Trigger Export |
- | ^ | + | |
- | ^ | + | |
- | ^ | + | |
---- | ---- | ||
- | === Waveform Generator (WaveGen) === | + | ===== Waveform Generator (WaveGen) |
- | |<100% 40%> | + | Supports the Waveform Generator, Network Analyzer, Impedance Analyzer, and Script Editor instruments. |
- | ^ Waveforms | + | |<100% 25% 25%>| |
- | ^ Update | + | ^ Waveforms |
- | ^ Resolution | + | ^ Update |
- | ^ Number of channels | + | ^ Resolution |
- | ^ Output | + | ^ Number of Channels |
- | ^ Sine | + | ^ Output |
- | ^ | + | ^ Switchable Filter |
- | ^ | + | ^ Sine |
- | ^ Total Harmonic Distortion (10 MHz) | -50 dBc || | + | | ::: |
- | ^ Spurious Free Dynamic Range (SFDR) | - 70 dB at 1 MHz (non-harmonic) | + | | ::: |
- | ^ | + | | ::: |
- | ^ Square | + | | ::: |
- | ^ | + | ^ Square |
- | ^ Rise / Fall time | <20ns (10% to 90%) || | + | | ::: |
- | ^ | + | | ::: |
- | ^ Jitter | 8ns cycle-to-cycle | + | | ::: |
- | ^ Ramp / Triangle | + | ^ Ramp / Triangle |
- | ^ Accuracy (with 10 kΩ load) | + | ^ Accuracy (with >10 kΩ load) ^ Amplitude (1 kHz sine) | ±(1% of output value ±5 mV) |
- | ^ Amplitude (1 kHz sine) | ±(1% of output value ± 5mV) || | + | | ::: |
- | ^ | + | ^ Output |
- | ^ Output | + | | ::: |
- | ^ 50 Ω | ± 6V || | + | ^ DC Offset |
- | ^ Hi-Z (> 10 kΩ) | ± 12V || | + | | ::: |
- | ^ DC offset | + | ^ Frequency |
- | ^ 50 Ω | ± 6V || | + | | ::: |
- | ^ Hi-Z (> 10 kΩ) | ± 12V || | + | ^ Arbitrary Waveforms |
- | ^ Frequency | + | | ::: |
- | ^ | + | ^ Protection |
- | ^ Resolution | 1 µHz || | + | |
- | ^ Arbitrary Waveforms | + | |
- | ^ | + | |
- | ^ Sample rate | 125 MS/s || | + | |
- | ^ Protection | + | |
**Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output. | **Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output. | ||
Line 119: | Line 123: | ||
{{ : | {{ : | ||
- | === Digital I/O === | + | ===== Digital I/O ===== |
- | |<100% 40%> | + | Supports the Static I/O and Script Editor instruments. |
- | ^ Number of channels | + | |<100% 40%>| |
- | ^ Direction | + | ^ Number of Channels |
- | ^ Logic Level | 5V compatible TTL input \\ 3.3V LVTTL output || | + | ^ Direction |
- | ^ Drive strength | + | ^ Logic Level | 5 V compatible TTL input \\ 3.3 V LVTTL output || |
- | ^ Input Voltage | 0 to 5V || | + | ^ Drive Strength |
- | ^ DIO channel pull resistors | + | ^ Input Voltage | 0 to 5 V || |
+ | ^ DIO Channel Pull Resistors | ||
**Note:** Digital I/O lines are designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | **Note:** Digital I/O lines are designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | ||
- | |||
- | **Note:** CLK0 & CLK0 are only available with the Virtualbench software. | ||
---- | ---- | ||
- | ===Digital Supply=== | + | ====Digital |
- | |<100% 40%> | + | |<100% 40%>| |
- | + | ^ Voltage | 3.3 V ± 10% | | |
- | ^ 3.3 V output | || | + | ^ Current | 20 mA | |
- | ^ | + | |
- | ^ | + | |
---- | ---- | ||
- | === DC Power Supply | + | ===== Digital Multimeter |
+ | |<100% 40%>| | ||
+ | ^ Functions | ||
+ | ^ Resolution | ||
+ | ^ Sample Rate | 5 S/s || | ||
+ | **Caution: | ||
- | ^ Outputs | || | + | === Input Protection === |
- | ^ 0 V to +6 V | 0 A to 1 A || | + | |
- | ^ 0 V to +25 V | 0 mA to 500 mA (isolated) || | + | |
- | ^ 0 V to -25 V | 0 mA to 500 mA (isolated) || | + | |
- | **Note: | + | |< |
- | + | ^ Resistance, | |
- | ---- | + | ^ DC and AC Voltage || Up to 300 V DC or 265 V AC (rms) 400 V AC (peak) | |
- | === Digital Multimeter === | + | ^ DC and AC Current |
- | |< | + | ^ ::: ^ DMM mA Current Connector Fuse | Internal ceramic fuse, 1.25 A 250 V, time-delay, 5 x 20 mm, T 1.25A H 250V (Bussman part number S505H-1.25-R at www.cooperindustries.com) | |
- | + | ||
- | ^ Functions | DC Voltage, AC Voltage, DC current, AC current, resistance, diode, continuity || | + | |
- | ^ Resolution | 5½ digits || | + | |
- | ^ Sample rate | 5 S/s || | + | |
- | ^ Input protection | || | + | |
- | ^ Resistance, | + | |
- | ^ | + | |
- | ^ DC and AC current | || | + | |
- | ^ | + | |
- | ^ DMM mA current connector fuse | Internal ceramic fuse, 1.25 A 250 V, time-delay, 5 x 20 mm, T 1.25A H 250V (Bussman part number S505H-1.25-R at www.cooperindustries.com) || | + | |
- | ^ Maximum common-mode voltage | 300 V DC or AC (rms) || | + | |
- | + | ||
- | **Caution: | + | |
**Caution: | **Caution: | ||
**Fuse:** When the fuse symbol is marked on a device, take proper precautions. | **Fuse:** When the fuse symbol is marked on a device, take proper precautions. | ||
+ | |||
+ | |<100% 40%>| | ||
+ | ^ Maximum common-mode voltage | 300 V DC or AC (rms) || | ||
---- | ---- | ||
Line 178: | Line 171: | ||
=== DC Voltage Accuracy === | === DC Voltage Accuracy === | ||
- | |<100% 25%> | + | |<100% 25%>| |
^ **Range** | **Input Impedance** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient | ^ **Range** | **Input Impedance** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient | ||
±(% of Reading + % of Range)/ | ±(% of Reading + % of Range)/ | ||
^ 100 mV* | <10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || | ^ 100 mV* | <10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || | ||
- | ^ 1 V | > 10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || | + | ^ 1 V | >10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || |
^ 10 V | >10 GΩ, 10 MΩ | 0.015 +0.005 | 0.001 + 0.0005 || | ^ 10 V | >10 GΩ, 10 MΩ | 0.015 +0.005 | 0.001 + 0.0005 || | ||
^ 100 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || | ^ 100 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || | ||
Line 190: | Line 183: | ||
---- | ---- | ||
=== DC Current Accuracy === | === DC Current Accuracy === | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ **Range** | **Burden Voltage** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient | |
- | ^ **Range** | **Burden Voltage** | **1-Year Accuracy**| ** ±(% of Reading + % of Range)** | ** Temperature Coefficient | + | |
±(% of Reading + % of Range)/C° ** || | ±(% of Reading + % of Range)/C° ** || | ||
^ 10 mA | <0.03 V | 0.070 + 0020 | 0.0035 + 0.0010 || | ^ 10 mA | <0.03 V | 0.070 + 0020 | 0.0035 + 0.0010 || | ||
Line 199: | Line 191: | ||
^ 10 A* | <0.3 V | 0.130 + 0.004 | 0.0045 + 0.0010 || | ^ 10 A* | <0.3 V | 0.130 + 0.004 | 0.0045 + 0.0010 || | ||
- | * 30 seconds on, 30 seconds off. Add 300 ppm for currents >2.2A. After measuring >5 A, | + | * 30 seconds on, 30 seconds off. Add 300 ppm for currents >2.2 A. After measuring >5 A, |
Wait two minutes to get full accuracy in the 1 A range. | Wait two minutes to get full accuracy in the 1 A range. | ||
---- | ---- | ||
=== DC Resistance Accuracy (2-Wire)*, 1V Open Circuit Voltage === | === DC Resistance Accuracy (2-Wire)*, 1V Open Circuit Voltage === | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ||
^ **Range** | **Short-Circuit Current** | **1-Year Accuracy ±(% of Reading + % of Range) ** | ** Temperature Coefficient | ^ **Range** | **Short-Circuit Current** | **1-Year Accuracy ±(% of Reading + % of Range) ** | ** Temperature Coefficient | ||
±(% of Reading + % of Range)/C° ** || | ±(% of Reading + % of Range)/C° ** || | ||
Line 222: | Line 212: | ||
**Caution: | **Caution: | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | ^ DC continuity accuracy range | 100 Ω || | + | ^ DC Continuity Accuracy Range | 100 Ω || |
- | ^ DC diode test range | 2 V || | + | ^ DC Diode Test Range | 2 V || |
^ Effective Common-Mode Rejection-Mode Ratio (CMRR), 1 kΩ resistance in LO lead | >100 dB || | ^ Effective Common-Mode Rejection-Mode Ratio (CMRR), 1 kΩ resistance in LO lead | >100 dB || | ||
- | ^ Normal-Mode | + | ^ Normal-Mode |
- | ^ Overrange | 105% of range except300 | + | ^ Overrange | 105% of range except 300 V || |
---- | ---- | ||
Line 233: | Line 223: | ||
===AC Voltage Accuracy=== | ===AC Voltage Accuracy=== | ||
- | |<100% 25%> | + | |<100% 25%>| |
^ **Range (rms)** | **Peak Voltage**| **Frequency** | ** 1-Year Accuracy ±(% of Reading + % of Range)**|**Temperature Coefficient ±(% of Reading + % of Range)/ | ^ **Range (rms)** | **Peak Voltage**| **Frequency** | ** 1-Year Accuracy ±(% of Reading + % of Range)**|**Temperature Coefficient ±(% of Reading + % of Range)/ | ||
^ 100 mV, 1 V, 10 V, 100 V, 265 V | ±210 mV, ±2.1 V, ±21 V, ±210 V, ±400 V | 20 Hz to 45 Hz | 0.91 + 0.10 | 0.01 + 0.005 || | ^ 100 mV, 1 V, 10 V, 100 V, 265 V | ±210 mV, ±2.1 V, ±21 V, ±210 V, ±400 V | 20 Hz to 45 Hz | 0.91 + 0.10 | 0.01 + 0.005 || | ||
- | ^ | | 45 Hz to 65 Hz | 0.30 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 45 Hz to 65 Hz | 0.30 + 0.05 | 0.01 + 0.005 || |
- | ^ | | 65 Hz to 1 kHz | 0.21 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 65 Hz to 1 kHz | 0.21 + 0.05 | 0.01 + 0.005 || |
- | ^ | | 1 kHz to 5 kHz | 0.12 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 1 kHz to 5 kHz | 0.12 + 0.05 | 0.01 + 0.005 || |
- | ^ | | 5 kHz to 20 kHz | 0.35 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 5 kHz to 20 kHz | 0.35 + 0.05 | 0.01 + 0.005 || |
---- | ---- | ||
===AC Current Accuracy=== | ===AC Current Accuracy=== | ||
- | |<100% 25%> | + | |<100% 25%>| |
^ **Range**|** Short-Circuit Current**| **Burden Voltage (rms)**| **Frequency**| ** 1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ±(% of Reading + % of Range)/C° ** || | ^ **Range**|** Short-Circuit Current**| **Burden Voltage (rms)**| **Frequency**| ** 1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ±(% of Reading + % of Range)/C° ** || | ||
^ 5 mA | ±10.5 mA | <0.02 | 20 Hz to 1 kHz | 0.20 + 0.01 | 0.01 + 0.005 || | ^ 5 mA | ±10.5 mA | <0.02 | 20 Hz to 1 kHz | 0.20 + 0.01 | 0.01 + 0.005 || | ||
Line 257: | Line 245: | ||
---- | ---- | ||
- | === DC Accuracy / Resolution | + | ===== DC Power Supply ===== |
- | |<100% 25%> | + | |
- | ^ **Output** | ** Type ** | ** +6V **| **+25V**|**-25V**|| | + | ^ Outputs |
- | ^ DC output | Voltage | + | ^ ::: | 0 V to +25 V | 0 mA to 500 mA (isolated) || |
- | ^ DC output | Current | 1 A | 500 mA | 500 mA || | + | ^ ::: | 0 V to -25 V | 0 mA to 500 mA (isolated) || |
- | ^ Programming accuracy, ±(% of reading + offset) | Voltage | + | |
- | ^ Programming accuracy, ±(% of reading + offset) | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA || | + | |
- | ^ Readback accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.1% + 20 mV | 0.1% + 20 mV || | + | |
- | ^ Readback accuracy, ±(% of reading + offset) | Current | + | |
- | ^ Programming Resolution | Voltage | 1.7 mV | 6.5 mV | 6.5 mV || | + | |
- | ^ Programming Resolution | Current | 0.30 mA | 0.15 mA | 0.15 mA || | + | |
- | ^ Readback resolution | Voltage | 0.41 mV | 1.7 mV | 1.7 mV || | + | |
- | ^ Readback resolution | Current | 70 µA | 35 µA | 35 µA || | + | |
- | ^ Load regulation ±(% of reading + offset) | Voltage | 0.01% + 25 mV | 0.03% + 5 mV | 0.03% + 5 mV || | + | |
+ | **Note: | ||
- | |<100% 25%> | ||
- | |||
- | ^ Overvoltage protection | 30 V (25 V channels) and 10 V (6 V channel) || | ||
- | ^ Reverse voltage protection | Reverse clamp diode, protected by self-resetting fuse || | ||
---- | ---- | ||
- | === External Trigger (TRIG) | + | === DC Accuracy / Resolution |
+ | |<100% 25%>| | ||
+ | ^ **Output** | ** Type ** | ** +6 V **| **+25 V**|**-25 V**|| | ||
+ | ^ DC Output | Voltage | 0 V to +6 V | 0 V to +25 V | 0 V to -25 V || | ||
+ | ^ ::: | Current | 1 A | 500 mA | 500 mA || | ||
+ | ^ Programming Accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.15% + 20 mV | 0.15% + 20 mV || | ||
+ | ^ ::: | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA || | ||
+ | ^ Readback Accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.15% + 20 mV | 0.15% + 20 mV || | ||
+ | ^ ::: | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15% + 4 mA || | ||
+ | ^ Programming Resolution | Voltage | 1.7 mV | 6.5 mV | 6.5 mV || | ||
+ | ^ ::: | Current | 0.30 mA | 0.15 mA | 0.15 mA || | ||
+ | ^ Readback Resolution | Voltage | 0.41 mV | 1.7 mV | 1.7 mV || | ||
+ | ^ ::: | Current | 70 µA | 35 µA | 35 µA || | ||
+ | ^ Load Regulation ±(% of reading + offset) | Voltage | 0.01% + 25 mV | 0.03% + 5 mV | 0.03% + 5 mV || | ||
- | |<100% 25%> | ||
- | ^ Direction | + | |<100% 25%>| |
+ | ^ Overvoltage Protection | 30 V (25 V channels) and 10 V (6 V channel) || | ||
+ | ^ Reverse Voltage Protection | Reverse clamp diode, protected by self-resetting fuse || | ||
+ | |||
+ | ---- | ||
+ | ===== External Trigger (TRIG) ===== | ||
+ | |||
+ | |<100% 25%>| | ||
+ | ^ Direction | ||
^ Logic Level | 5 V compatible TTL input, 3.3 V LVLTTL output || | ^ Logic Level | 5 V compatible TTL input, 3.3 V LVLTTL output || | ||
- | ^ Drive strength | + | ^ Drive Strength |
- | ^ Input voltage | + | ^ Input Voltage |
- | **Note:** The external trigger line is designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. It is not recommended for use with signals likely to exceed | + | **Note:** The external trigger line is designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. It is not recommended for use with signals likely to exceed |
---- | ---- | ||
- | ==== Features ==== | + | ===== Features |
- | === Spectrum Analyzer === | + | ==== Spectrum Analyzer |
- | |<100% 25%> | + | |<100% 25%>| |
^ Frequency Range | DC to maximum bandwidth of scope || | ^ Frequency Range | DC to maximum bandwidth of scope || | ||
- | ^ Display | + | ^ Display |
- | ^ Y axis | Logarithmic (dbV, dBu, dBm,) or linear (volts) || | + | ^ Y Axis | Logarithmic (dbV, dBu, dBm) or linear (volts) || |
- | ^ X axis | Linear or logarithmic || | + | ^ X Axis | Linear or logarithmic || |
- | ^ Windowing | + | ^ Windowing |
---- | ---- | ||
- | === Network Analyzer === | + | ==== Network Analyzer |
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ Frequency Range | 1 mHz to 10 MHz, up to 10k samples per decade || | |
- | + | ^ Display | |
- | ^ Frequency Range | 1 mHz to 10MHz, up to 10k samples per decade || | + | ^ Y Axis | Linear or logarithmic || |
- | ^ Display | + | ^ X Axis | Linear or logarithmic || |
- | ^ Y axis | Linear or logarithmic || | + | |
- | ^ X axis | Linear or logarithmic || | + | |
^ Plots | Time, FFT, Nichols, Nyquist || | ^ Plots | Time, FFT, Nichols, Nyquist || | ||
---- | ---- | ||
- | === Math Channels === | + | ==== Math Channels ==== |
- | + | ||
- | |<100% 25%> | + | |
+ | |<100% 25%>| | ||
^ Operations | addition “+”, subtraction “-”, multiplication “*”, division “/”, reminder “%”. || | ^ Operations | addition “+”, subtraction “-”, multiplication “*”, division “/”, reminder “%”. || | ||
^ Brackets | parentheses (), square brackets [] || | ^ Brackets | parentheses (), square brackets [] || | ||
Line 326: | Line 318: | ||
---- | ---- | ||
- | === Automatic Measurements (analog channels only) === | + | ==== Automatic Measurements (Analog Channels Only) ==== |
- | + | ||
- | |<100% 25%> | + | |
- | ^ Oscilloscope | + | |<100% 25%>| |
- | ^ Spectrum | + | ^ Oscilloscope |
+ | ^ Spectrum | ||
^ Statistics | Logarithmic (dbV, dBu, dBm,) or linear (volts) || | ^ Statistics | Logarithmic (dbV, dBu, dBm,) or linear (volts) || | ||
---- | ---- | ||
- | ==== Connectivity ==== | + | ===== Connectivity |
- | === Wired USB Interface === | + | ==== Wired USB Interface |
- | |<100% 25%> | + | |<100% 25%>| |
- | ^ USB specification | + | ^ USB Specification |
---- | ---- | ||
- | ==== Power Requirements ==== | + | ===== Power Requirements |
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ Voltage | |
- | ^ Voltage | + | ^ Power Consumption |
- | ^ Power consumption | + | ^ Power Input Connector |
- | ^ Power input connector | + | ^ Power Disconnect |
- | ^ Power disconnect | + | |
---- | ---- | ||
- | ==== Physical Characteristics ==== | + | ===== Physical Characteristics |
- | |<100% 25%> | + | |<100% 25%>| |
^ Enclosure | 25.40 cm x 19.05 cm x 7.77 cm \\ (10.00 in x 7.50 in x 3.06 in) || | ^ Enclosure | 25.40 cm x 19.05 cm x 7.77 cm \\ (10.00 in x 7.50 in x 3.06 in) || | ||
^ Weight | 2.05 kg (4 lb 8.3 oz) || | ^ Weight | 2.05 kg (4 lb 8.3 oz) || | ||
- | ^ Security | + | ^ Security |
---- | ---- | ||
Line 365: | Line 355: | ||
**Note:** Use the ADP5250 in a horizontal orientation. Allow at least 10.16 cm (4.0 in.) of clearance in front and behind the ADP5250 for USB, power, and common connector cabling. | **Note:** Use the ADP5250 in a horizontal orientation. Allow at least 10.16 cm (4.0 in.) of clearance in front and behind the ADP5250 for USB, power, and common connector cabling. | ||
- | ==== Safety Voltages ==== | + | ===== Safety Voltages |
Connect only voltages that are within these limits. | Connect only voltages that are within these limits. | ||
- | === DMM Isolation Voltages (Ground to Earth) === | + | ==== DMM Isolation Voltages (Ground to Earth) |
- | |<100% 25%> | + | |
+ | <columns 100% 5% 95%> | ||
+ | {{: | ||
+ | < | ||
+ | **Hazardous Voltage:** This icon denotes a warning advising you to take precautions to avoid electrical shock. | ||
+ | </ | ||
+ | |||
+ | === Channel-to-earth Ground | ||
+ | |<100% 25%>| | ||
^ Continuous | 300 V, Measurement Category II || | ^ Continuous | 300 V, Measurement Category II || | ||
^ Withstand | 3000 V (RMS), verified by a 5 s dielectric withstand test || | ^ Withstand | 3000 V (RMS), verified by a 5 s dielectric withstand test || | ||
Line 377: | Line 375: | ||
Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, | Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, | ||
- | === DC Power Supply Isolation Voltages === | + | <columns 100% 5% 95%> |
- | |<100% 25%> | + | {{: |
- | ^ +25V and -25V to earth ground, continuous | 60VDC, Measurement Category 1 ||| | + | < |
+ | **Caution: | ||
+ | </ | ||
+ | |||
+ | ==== DC Power Supply Isolation Voltages | ||
+ | |<100% 25%>| | ||
+ | ^ +25V and -25V to earth ground, continuous | 60 VDC, Measurement Category 1 ||| | ||
+ | |||
+ | **Note:** // | ||
---- | ---- | ||
- | ====Environmental==== | + | =====Environmental===== |
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ Operating | |
- | ^ Operating | + | ^ Storage |
- | ^ Storage | + | ^ Operating |
- | ^ Operating | + | ^ Storage |
- | ^ Storage | + | |
^ Cooling | Forced air circulation (positive pressurization) through a fan. Fan speed automatically adjusts according to operating conditions. Intake and exhaust locations are on rear of device. Ensure that the intake and exhaust locations are not obstructed. || | ^ Cooling | Forced air circulation (positive pressurization) through a fan. Fan speed automatically adjusts according to operating conditions. Intake and exhaust locations are on rear of device. Ensure that the intake and exhaust locations are not obstructed. || | ||
^ Pollution Degree | 2 || | ^ Pollution Degree | 2 || | ||
- | ^ Maximum | + | ^ Maximum |
**Note:** For indoor use only. | **Note:** For indoor use only. | ||
Line 398: | Line 403: | ||
==== Shock and Vibration ==== | ==== Shock and Vibration ==== | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ Operational | |
- | ^ Operational | + | ^ Random |
- | ^ Random | + | ^ Random |
- | ^ Random | + | |
---- | ---- | ||
- | + | {{page> | |
- | ==== Safety ==== | + | |
- | This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, | + | |
- | * IEC 61010-1, EN 61010-1 | + | |
- | * UL 61010-1, CSA 61010-1 | + | |
---- | ---- | ||
- | + | All specifications provided courtesy | |
- | ==== Electromagnetic Compatibility ==== | + | |
- | + | ||
- | This product meets the requirements | + | |
- | * EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity | + | |
- | * EN 55011 (CISPR 11): Group 1, Class A emissions | + | |
- | * EN 55022 (CISPR 22): Class A emissions | + | |
- | * EN 55024 (CISPR 24): Immunity | + | |
- | * AS/NZS CISPR 11: Group 1, Class A emissions | + | |
- | * AS/NZS CISPR 22: Class A emissions | + | |
- | * FCC 47 CFR Part 15B: Class A emissions | + | |
- | * ICES-001: Class A emissions | + | |
- | + | ||
- | **Note:** In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, | + | |
- | + | ||
- | **Note:** Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes. | + | |
- | + | ||
- | **Note:** For EMC declarations and certifications, | + | |
- | + | ||
- | + | ||
- | ---- | + | |
- | + | ||
- | ====CE Compliance==== | + | |
- | This product meets the essential requirements of applicable European Directives, as follows: | + | |
- | * 2014/35/EU; Low-Voltage Directive (safety) | + | |
- | * 2014/30/EU; Electromagnetic Compatibility Directive (EMC) | + | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + |