Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
test-and-measurement:analog-discovery-pro-5250:specifications [2021/10/11 17:56] – removed Data Logger and Voltmeter from Analog Input supported instruments list James Colvin | test-and-measurement:analog-discovery-pro-5250:specifications [2023/12/18 19:55] (current) – James Colvin | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Analog Discovery Pro ADP5250 Specifications ====== | + | ====== Analog Discovery Pro (ADP5250) Specifications ====== |
+ | /* | ||
+ | Additional material for ADP5470 and ADP5490. | ||
+ | https:// | ||
+ | https:// | ||
+ | |||
+ | https:// | ||
+ | https:// | ||
+ | |||
+ | PDFs of NI publicly published Specifications, | ||
+ | |||
+ | */ | ||
+ | |||
~~TechArticle~~ | ~~TechArticle~~ | ||
These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted. | These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted. | ||
Line 6: | Line 19: | ||
==== Analog Input Channels ==== | ==== Analog Input Channels ==== | ||
- | Supports the Oscilloscope, | + | Supports the Oscilloscope, Data Logger, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments. |
=== Vertical System === | === Vertical System === | ||
Line 14: | Line 27: | ||
^ Bandwidth (-3 dB) | 100 MHz || | ^ Bandwidth (-3 dB) | 100 MHz || | ||
^ Resolution | 8 bits || | ^ Resolution | 8 bits || | ||
- | ^ Accuracy | ± 2% of input ±1% full scale (V peak to peak) || | + | ^ Accuracy | ±2% of input ±1% full scale (V peak to peak) || |
- | ^ Input coupling | + | ^ Input Coupling |
^ Vertical Sensitivity (range) | 10 mV / div (100 mV peak to peak) \\ 20 mV / div (200 mV peak to peak) \\ 50 mV / div (400 mV peak to peak) \\ 100 mV / div (1 V peak to peak) \\ 200 mV / div (2 V peak to peak) \\ 500 mV / div (4 V peak to peak) \\ 1 V / div (10 V peak to peak) \\ 2 V / div (20 V peak to peak) \\ 5 V / div (40 V peak to peak)|| | ^ Vertical Sensitivity (range) | 10 mV / div (100 mV peak to peak) \\ 20 mV / div (200 mV peak to peak) \\ 50 mV / div (400 mV peak to peak) \\ 100 mV / div (1 V peak to peak) \\ 200 mV / div (2 V peak to peak) \\ 500 mV / div (4 V peak to peak) \\ 1 V / div (10 V peak to peak) \\ 2 V / div (20 V peak to peak) \\ 5 V / div (40 V peak to peak)|| | ||
- | ^ Input impedance | + | ^ Input Impedance |
- | ^ Acquisition | + | ^ Acquisition |
- | ^ DC Offset Range | 10 mV/div, 20 mV/div, 50 mV/ | + | ^ DC Offset Range | 10 mV/div, 20 mV/div, 50 mV/ |
---- | ---- | ||
=== Horizontal System === | === Horizontal System === | ||
- | |< | + | |< |
- | ^ Maximum | + | ^ Maximum |
- | ^ Maximum | + | ^ Maximum |
---- | ---- | ||
==== Digital Channels / Logic Analyzer ==== | ==== Digital Channels / Logic Analyzer ==== | ||
+ | Supports the Logic Analyzer and Script Editor instruments. | ||
{{ : | {{ : | ||
- | |||
- | |||
=== Vertical System === | === Vertical System === | ||
- | |<100% 40%> | + | |<100% 40%>| |
- | ^ Number of channels | + | ^ Number of Channels |
^ Maximum Input Frequency | 100 MHz || | ^ Maximum Input Frequency | 100 MHz || | ||
- | ^ Input voltage | + | ^ Input Voltage |
- | ^ Input current | + | ^ Input Current |
- | ^ Input threshold | + | ^ Input Threshold |
^ Threshold Accuracy | 350 mV || | ^ Threshold Accuracy | 350 mV || | ||
- | ^ Input Impedance | 100 kΩ \\ 7.5 pF pulled to -2.0V to +6.5V, varies with input threshold setting || | + | ^ Input Impedance | 100 kΩ ││ |
- | ^ Additional / Internal | + | ^ Additional / Internal |
**Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | **Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | ||
- | === Horizontal System === | + | ~~REFNOTES~~ |
- | |<100% 40%> | + | |
- | ^ Timing | + | === Horizontal System === |
- | ^ Maximum | + | |<100% 40%>| |
+ | ^ Timing | ||
+ | ^ Maximum | ||
^ Record Length (Typical) | 1 MS || | ^ Record Length (Typical) | 1 MS || | ||
^ Record Length (Minimum) | 4 kS || | ^ Record Length (Minimum) | 4 kS || | ||
- | ^ Decimation | External Sample Clock, 1:1, 2:1, and n*4:1 where n is in an integer || | + | ^ Decimation | External Sample Clock, 1:1, 2:1, and n*4:1 where n is an integer || |
- | ^ Maximum Sample Compression | 2^15 to 1 || | + | ^ Maximum Sample Compression | 2<sup>15</ |
- | --- | + | ---- |
- | === Triggering === | + | ==== Triggering ==== |
+ | |<100% 20% 20%>| | ||
+ | ^ Trigger Modes || Normal, Auto, Force, Single | ||
+ | ^ Trigger Sources | ||
+ | ^ Trigger Types ^ Analog | ||
+ | ^ ::: ^ Digital | ||
+ | ^ Trigger Resolution ^ Analog / Oscilloscope | ||
+ | ^ ::: ^ Digital / Logic Analyzer | ||
+ | ^ Trigger Export | ||
- | |<100% 40%> | + | ---- |
- | ^ Trigger modes | Normal, Auto, Force, Single || | + | |
- | ^ Trigger sources | Oscilloscope analog channels \\ Oscilloscope digital channels \\ Function generator start \\ Digital I/O lines \\ External trigger (TRIG) \\ Power line frequency || | + | |
- | ^ Trigger Types | || | + | |
- | ^ | + | |
- | ^ | + | |
- | ^ Trigger Resolution | || | + | |
- | ^ | + | |
- | ^ | + | |
- | ^ | + | |
- | --- | + | ===== Waveform Generator (WaveGen) ===== |
+ | Supports the Waveform Generator, Network Analyzer, Impedance Analyzer, and Script Editor instruments. | ||
- | === Waveform Generator (WaveGen) === | + | |< |
- | |< | + | ^ Waveforms |
- | + | ^ Update | |
- | ^ Waveforms | Sine, square, ramp / triangle, DC, arbitrary | + | ^ Resolution |
- | ^ Update | + | ^ Number of Channels |
- | ^ Resolution | 14 bits || | + | ^ Output |
- | ^ Number of channels | + | ^ Switchable Filter |
- | ^ Output | + | ^ Sine |
- | ^ Sine | || | + | | ::: |
- | ^ | + | | ::: |
- | ^ | + | | ::: |
- | ^ | + | | ::: |
- | ^ | + | ^ Square |
- | ^ | + | | ::: |
- | ^ Square | + | | ::: |
- | ^ | + | | ::: |
- | ^ | + | ^ Ramp / Triangle |
- | ^ | + | ^ Accuracy (with >10 kΩ load) ^ Amplitude (1 kHz sine) | ±(1% of output value ±5 mV) |
- | ^ | + | | ::: |
- | ^ Ramp / Triangle | + | ^ Output |
- | ^ Accuracy (with 10 kΩ load) | || | + | | ::: |
- | ^ Amplitude (1 kHz sine) | ±(1% of output value ± 5mV) || | + | ^ DC Offset |
- | ^ DC | ±(1% of output value ± 5mV) || | + | | ::: |
- | ^ Output | + | ^ Frequency |
- | ^ 50 Ω | ± 6V || | + | | ::: |
- | ^ Hi-Z (> 10 kΩ) | ± 12V || | + | ^ Arbitrary Waveforms |
- | ^ DC offset | || | + | | ::: |
- | ^ 50 Ω | ± 6V || | + | ^ Protection |
- | ^ Hi-Z (> 10 kΩ) | ± 12V || | + | |
- | ^ Frequency | + | |
- | ^ Accuracy | ≤ 100 ppm || | + | |
- | ^ Resolution | 1 µHz || | + | |
- | ^ Arbitrary Waveforms | + | |
- | ^ Points | 1 MS || | + | |
- | ^ Sample | + | |
- | ^ Flatness | + | |
- | ^ Protection | + | |
**Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output. | **Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output. | ||
- | --- | + | ---- |
{{ : | {{ : | ||
- | === Digital I/O === | + | ===== Digital I/O ===== |
- | |<100% 40%> | + | Supports the Static I/O and Script Editor instruments. |
- | ^ Number of channels | + | |<100% 40%>| |
- | ^ Direction | + | ^ Number of Channels |
- | ^ Logic Level | 5V compatible TTL input \\ 3.3V LVTTL output || | + | ^ Direction |
- | ^ Drive strength | + | ^ Logic Level | 5 V compatible TTL input \\ 3.3 V LVTTL output || |
- | ^ Input Voltage | 0 to 5V || | + | ^ Drive Strength |
- | ^ DIO channel pull resistors | + | ^ Input Voltage | 0 to 5 V || |
+ | ^ DIO Channel Pull Resistors | ||
**Note:** Digital I/O lines are designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | **Note:** Digital I/O lines are designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. | ||
+ | ---- | ||
- | **Note:** CLK0 & CLK0 are only available with the Virtualbench software. | + | ====Digital Power Supply==== |
- | --- | + | |<100% 40%>| |
+ | ^ Voltage | 3.3 V ± 10% | | ||
+ | ^ Current | 20 mA | | ||
- | ===Digital | + | ---- |
- | |<100% 40%> | + | ===== Digital |
+ | |<100% 40%>| | ||
+ | ^ Functions | ||
+ | ^ Resolution | ||
+ | ^ Sample Rate | 5 S/s || | ||
- | ^ 3.3 V output | + | **Caution: |
- | ^ | + | |
- | ^ | + | |
- | --- | + | |
- | === DC Power Supply | + | === Input Protection |
- | + | |< | |
- | ^ Outputs | || | + | ^ Resistance, |
- | ^ 0 V to +6 V | 0 A to 1 A || | + | ^ DC and AC Voltage || Up to 300 V DC or 265 V AC (rms) 400 V AC (peak) | |
- | ^ 0 V to +25 V | 0 mA to 500 mA (isolated) || | + | ^ DC and AC Current |
- | ^ 0 V to -25 V | 0 mA to 500 mA (isolated) || | + | ^ ::: ^ DMM mA Current Connector Fuse | Internal ceramic fuse, 1.25 A 250 V, time-delay, 5 x 20 mm, T 1.25A H 250V (Bussman part number S505H-1.25-R at www.cooperindustries.com) | |
- | + | ||
- | **Note: | + | |
- | --- | + | |
- | + | ||
- | === Digital Multimeter === | + | |
- | |< | + | |
- | + | ||
- | ^ Functions | DC Voltage, AC Voltage, DC current, AC current, resistance, diode, continuity || | + | |
- | ^ Resolution | 5½ digits || | + | |
- | ^ Sample rate | 5 S/s || | + | |
- | ^ Input protection | || | + | |
- | ^ Resistance, | + | |
- | ^ | + | |
- | ^ DC and AC current | || | + | |
- | ^ | + | |
- | ^ DMM mA current connector fuse | Internal ceramic fuse, 1.25 A 250 V, time-delay, 5 x 20 mm, T 1.25A H 250V (Bussman part number S505H-1.25-R at www.cooperindustries.com) || | + | |
- | ^ Maximum common-mode voltage | 300 V DC or AC (rms) || | + | |
- | + | ||
- | **Caution: | + | |
**Caution: | **Caution: | ||
Line 174: | Line 163: | ||
**Fuse:** When the fuse symbol is marked on a device, take proper precautions. | **Fuse:** When the fuse symbol is marked on a device, take proper precautions. | ||
- | --- | + | |<100% 40%>| |
+ | ^ Maximum common-mode voltage | 300 V DC or AC (rms) || | ||
+ | ---- | ||
====DC==== | ====DC==== | ||
=== DC Voltage Accuracy === | === DC Voltage Accuracy === | ||
- | |<100% 25%> | + | |<100% 25%>| |
^ **Range** | **Input Impedance** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient | ^ **Range** | **Input Impedance** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient | ||
±(% of Reading + % of Range)/ | ±(% of Reading + % of Range)/ | ||
^ 100 mV* | <10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || | ^ 100 mV* | <10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || | ||
- | ^ 1 V | > 10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || | + | ^ 1 V | >10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || |
^ 10 V | >10 GΩ, 10 MΩ | 0.015 +0.005 | 0.001 + 0.0005 || | ^ 10 V | >10 GΩ, 10 MΩ | 0.015 +0.005 | 0.001 + 0.0005 || | ||
^ 100 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || | ^ 100 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || | ||
^ 300 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || | ^ 300 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || | ||
* Add 15 µV if not immediately following offset null. | * Add 15 µV if not immediately following offset null. | ||
- | --- | ||
+ | ---- | ||
=== DC Current Accuracy === | === DC Current Accuracy === | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ **Range** | **Burden Voltage** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient | |
- | ^ **Range** | **Burden Voltage** | **1-Year Accuracy**| ** ±(% of Reading + % of Range)** | ** Temperature Coefficient | + | |
±(% of Reading + % of Range)/C° ** || | ±(% of Reading + % of Range)/C° ** || | ||
^ 10 mA | <0.03 V | 0.070 + 0020 | 0.0035 + 0.0010 || | ^ 10 mA | <0.03 V | 0.070 + 0020 | 0.0035 + 0.0010 || | ||
Line 202: | Line 191: | ||
^ 10 A* | <0.3 V | 0.130 + 0.004 | 0.0045 + 0.0010 || | ^ 10 A* | <0.3 V | 0.130 + 0.004 | 0.0045 + 0.0010 || | ||
- | * 30 seconds on, 30 seconds off. Add 300 ppm for currents >2.2A. After measuring >5 A, | + | * 30 seconds on, 30 seconds off. Add 300 ppm for currents >2.2 A. After measuring >5 A, |
Wait two minutes to get full accuracy in the 1 A range. | Wait two minutes to get full accuracy in the 1 A range. | ||
- | --- | + | ---- |
=== DC Resistance Accuracy (2-Wire)*, 1V Open Circuit Voltage === | === DC Resistance Accuracy (2-Wire)*, 1V Open Circuit Voltage === | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ||
^ **Range** | **Short-Circuit Current** | **1-Year Accuracy ±(% of Reading + % of Range) ** | ** Temperature Coefficient | ^ **Range** | **Short-Circuit Current** | **1-Year Accuracy ±(% of Reading + % of Range) ** | ** Temperature Coefficient | ||
±(% of Reading + % of Range)/C° ** || | ±(% of Reading + % of Range)/C° ** || | ||
Line 222: | Line 208: | ||
* Perform offset nulling | * Perform offset nulling | ||
- | --- | + | ---- |
**Caution: | **Caution: | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | ^ DC continuity accuracy range | 100 Ω || | + | ^ DC Continuity Accuracy Range | 100 Ω || |
- | ^ DC diode test range | 2 V || | + | ^ DC Diode Test Range | 2 V || |
^ Effective Common-Mode Rejection-Mode Ratio (CMRR), 1 kΩ resistance in LO lead | >100 dB || | ^ Effective Common-Mode Rejection-Mode Ratio (CMRR), 1 kΩ resistance in LO lead | >100 dB || | ||
- | ^ Normal-Mode | + | ^ Normal-Mode |
- | ^ Overrange | 105% of range except300 | + | ^ Overrange | 105% of range except 300 V || |
- | --- | + | |
+ | ---- | ||
====AC==== | ====AC==== | ||
===AC Voltage Accuracy=== | ===AC Voltage Accuracy=== | ||
- | |<100% 25%> | + | |<100% 25%>| |
^ **Range (rms)** | **Peak Voltage**| **Frequency** | ** 1-Year Accuracy ±(% of Reading + % of Range)**|**Temperature Coefficient ±(% of Reading + % of Range)/ | ^ **Range (rms)** | **Peak Voltage**| **Frequency** | ** 1-Year Accuracy ±(% of Reading + % of Range)**|**Temperature Coefficient ±(% of Reading + % of Range)/ | ||
^ 100 mV, 1 V, 10 V, 100 V, 265 V | ±210 mV, ±2.1 V, ±21 V, ±210 V, ±400 V | 20 Hz to 45 Hz | 0.91 + 0.10 | 0.01 + 0.005 || | ^ 100 mV, 1 V, 10 V, 100 V, 265 V | ±210 mV, ±2.1 V, ±21 V, ±210 V, ±400 V | 20 Hz to 45 Hz | 0.91 + 0.10 | 0.01 + 0.005 || | ||
- | ^ | | 45 Hz to 65 Hz | 0.30 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 45 Hz to 65 Hz | 0.30 + 0.05 | 0.01 + 0.005 || |
- | ^ | | 65 Hz to 1 kHz | 0.21 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 65 Hz to 1 kHz | 0.21 + 0.05 | 0.01 + 0.005 || |
- | ^ | | 1 kHz to 5 kHz | 0.12 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 1 kHz to 5 kHz | 0.12 + 0.05 | 0.01 + 0.005 || |
- | ^ | | 5 kHz to 20 kHz | 0.35 + 0.05 | 0.01 + 0.005 || | + | ^ ::: | ::: | 5 kHz to 20 kHz | 0.35 + 0.05 | 0.01 + 0.005 || |
- | --- | + | |
+ | ---- | ||
===AC Current Accuracy=== | ===AC Current Accuracy=== | ||
- | |<100% 25%> | + | |<100% 25%>| |
^ **Range**|** Short-Circuit Current**| **Burden Voltage (rms)**| **Frequency**| ** 1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ±(% of Reading + % of Range)/C° ** || | ^ **Range**|** Short-Circuit Current**| **Burden Voltage (rms)**| **Frequency**| ** 1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ±(% of Reading + % of Range)/C° ** || | ||
^ 5 mA | ±10.5 mA | <0.02 | 20 Hz to 1 kHz | 0.20 + 0.01 | 0.01 + 0.005 || | ^ 5 mA | ±10.5 mA | <0.02 | 20 Hz to 1 kHz | 0.20 + 0.01 | 0.01 + 0.005 || | ||
Line 260: | Line 244: | ||
^ 5 A | ±1.05 A | <0.02 V | 1 kHz to 5 kHz | 0.60 + 0.03 | 0.01 + 0.005 || | ^ 5 A | ±1.05 A | <0.02 V | 1 kHz to 5 kHz | 0.60 + 0.03 | 0.01 + 0.005 || | ||
- | --- | + | ---- |
- | + | ===== DC Power Supply ===== | |
- | === DC Accuracy / Resolution | + | |
- | |<100% 25%> | + | |
- | ^ **Output** | ** Type ** | ** +6V **| **+25V**|**-25V**|| | + | ^ Outputs |
- | ^ DC output | Voltage | + | ^ ::: | 0 V to +25 V | 0 mA to 500 mA (isolated) || |
- | ^ DC output | Current | 1 A | 500 mA | 500 mA || | + | ^ ::: | 0 V to -25 V | 0 mA to 500 mA (isolated) || |
- | ^ Programming accuracy, ±(% of reading + offset) | Voltage | + | |
- | ^ Programming accuracy, ±(% of reading + offset) | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA || | + | |
- | ^ Readback accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.1% + 20 mV | 0.1% + 20 mV || | + | |
- | ^ Readback accuracy, ±(% of reading + offset) | Current | + | |
- | ^ Programming Resolution | Voltage | 1.7 mV | 6.5 mV | 6.5 mV || | + | |
- | ^ Programming Resolution | Current | 0.30 mA | 0.15 mA | 0.15 mA || | + | |
- | ^ Readback resolution | Voltage | 0.41 mV | 1.7 mV | 1.7 mV || | + | |
- | ^ Readback resolution | Current | 70 µA | 35 µA | 35 µA || | + | |
- | ^ Load regulation ±(% of reading + offset) | Voltage | 0.01% + 25 mV | 0.03% + 5 mV | 0.03% + 5 mV || | + | |
+ | **Note: | ||
- | |<100% 25%> | ||
- | |||
- | ^ Overvoltage protection | 30 V (25 V channels) and 10 V (6 V channel) || | ||
- | ^ Reverse voltage protection | Reverse clamp diode, protected by self-resetting fuse || | ||
- | --- | + | ---- |
+ | === DC Accuracy / Resolution === | ||
+ | |<100% 25%>| | ||
+ | ^ **Output** | ** Type ** | ** +6 V **| **+25 V**|**-25 V**|| | ||
+ | ^ DC Output | Voltage | 0 V to +6 V | 0 V to +25 V | 0 V to -25 V || | ||
+ | ^ ::: | Current | 1 A | 500 mA | 500 mA || | ||
+ | ^ Programming Accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.15% + 20 mV | 0.15% + 20 mV || | ||
+ | ^ ::: | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA || | ||
+ | ^ Readback Accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.15% + 20 mV | 0.15% + 20 mV || | ||
+ | ^ ::: | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15% + 4 mA || | ||
+ | ^ Programming Resolution | Voltage | 1.7 mV | 6.5 mV | 6.5 mV || | ||
+ | ^ ::: | Current | 0.30 mA | 0.15 mA | 0.15 mA || | ||
+ | ^ Readback Resolution | Voltage | 0.41 mV | 1.7 mV | 1.7 mV || | ||
+ | ^ ::: | Current | 70 µA | 35 µA | 35 µA || | ||
+ | ^ Load Regulation ±(% of reading + offset) | Voltage | 0.01% + 25 mV | 0.03% + 5 mV | 0.03% + 5 mV || | ||
- | === External Trigger (TRIG) === | ||
- | |<100% 25%> | + | |<100% 25%>| |
+ | ^ Overvoltage Protection | 30 V (25 V channels) and 10 V (6 V channel) || | ||
+ | ^ Reverse Voltage Protection | Reverse clamp diode, protected by self-resetting fuse || | ||
- | ^ Direction | + | ---- |
+ | ===== External Trigger (TRIG) ===== | ||
+ | |||
+ | |<100% 25%>| | ||
+ | ^ Direction | ||
^ Logic Level | 5 V compatible TTL input, 3.3 V LVLTTL output || | ^ Logic Level | 5 V compatible TTL input, 3.3 V LVLTTL output || | ||
- | ^ Drive strength | + | ^ Drive Strength |
- | ^ Input voltage | + | ^ Input Voltage |
- | **Note:** The external trigger line is designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. It is not recommended for use with signals likely to exceed | + | **Note:** The external trigger line is designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. It is not recommended for use with signals likely to exceed |
- | --- | + | ---- |
+ | ===== Features ===== | ||
- | ==== Features | + | ==== Spectrum Analyzer |
- | === Spectrum Analyzer === | + | |<100% 25%>| |
- | + | ||
- | |<100% 25%> | + | |
^ Frequency Range | DC to maximum bandwidth of scope || | ^ Frequency Range | DC to maximum bandwidth of scope || | ||
- | ^ Display | + | ^ Display |
- | ^ Y axis | Logarithmic (dbV, dBu, dBm,) or linear (volts) || | + | ^ Y Axis | Logarithmic (dbV, dBu, dBm) or linear (volts) || |
- | ^ X axis | Linear or logarithmic || | + | ^ X Axis | Linear or logarithmic || |
- | ^ Windowing | + | ^ Windowing |
- | --- | + | ---- |
- | + | ==== Network Analyzer | |
- | === Network Analyzer === | + | |<100% 25%>| |
- | |<100% 25%> | + | ^ Frequency Range | 1 mHz to 10 MHz, up to 10k samples per decade || |
- | + | ^ Display | |
- | + | ^ Y Axis | Linear or logarithmic || | |
- | ^ Frequency Range | 1 mHz to 10MHz, up to 10k samples per decade || | + | ^ X Axis | Linear or logarithmic || |
- | ^ Display | + | |
- | ^ Y axis | Linear or logarithmic || | + | |
- | ^ X axis | Linear or logarithmic || | + | |
^ Plots | Time, FFT, Nichols, Nyquist || | ^ Plots | Time, FFT, Nichols, Nyquist || | ||
- | --- | + | ---- |
- | + | ==== Math Channels ==== | |
- | === Math Channels === | + | |
- | + | ||
- | |<100% 25%> | + | |
+ | |<100% 25%>| | ||
^ Operations | addition “+”, subtraction “-”, multiplication “*”, division “/”, reminder “%”. || | ^ Operations | addition “+”, subtraction “-”, multiplication “*”, division “/”, reminder “%”. || | ||
^ Brackets | parentheses (), square brackets [] || | ^ Brackets | parentheses (), square brackets [] || | ||
Line 334: | Line 317: | ||
^ Operands | All analog and digital input channels, reference waveforms, time, constants, Pi || | ^ Operands | All analog and digital input channels, reference waveforms, time, constants, Pi || | ||
- | --- | + | ---- |
- | + | ==== Automatic Measurements (Analog Channels Only) ==== | |
- | === Automatic Measurements (analog channels only) === | + | |
- | + | ||
- | |<100% 25%> | + | |
- | ^ Oscilloscope | + | |<100% 25%>| |
- | ^ Spectrum | + | ^ Oscilloscope |
+ | ^ Spectrum | ||
^ Statistics | Logarithmic (dbV, dBu, dBm,) or linear (volts) || | ^ Statistics | Logarithmic (dbV, dBu, dBm,) or linear (volts) || | ||
- | --- | + | ---- |
+ | ===== Connectivity ===== | ||
- | ==== Connectivity | + | ==== Wired USB Interface |
- | === Wired USB Interface === | + | |<100% 25%>| |
+ | ^ USB Specification | USB 2.0 Hi-Speed || | ||
- | |<100% 25%> | + | ---- |
- | ^ USB specification | + | ===== Power Requirements ===== |
+ | |<100% 25%>| | ||
+ | ^ Voltage Input Range | 100 V AC to 240 V AC, ±10%, 50/60 Hz || | ||
+ | ^ Power Consumption | 100 W maximum || | ||
+ | ^ Power Input Connector | IEC C13 power connector || | ||
+ | ^ Power Disconnect | The AC power cable provides main power disconnect. Do not position the equipment so that it is difficult to disconnect the power cable. Depressing the front panel power button does not inhibit the internal power supply. || | ||
- | --- | + | ---- |
+ | ===== Physical Characteristics ===== | ||
- | ==== Power Requirements ==== | + | |<100% 25%>| |
- | |<100% 25%> | + | |
- | + | ||
- | ^ Voltage input range | 100 VAC to 240 VAC, 50/60 Hz || | + | |
- | ^ Power consumption | 100 W maximum || | + | |
- | ^ Power input connector | IEC C13 power connector || | + | |
- | ^ Power disconnect | The AC power cable provides main power disconnect. Do not position the equipment so that it is difficult to disconnect the power cable. Depressing the front panel power button does not inhibit the internal power supply. || | + | |
- | + | ||
- | --- | + | |
- | + | ||
- | ==== Physical Characteristics ==== | + | |
- | + | ||
- | |<100% 25%> | + | |
^ Enclosure | 25.40 cm x 19.05 cm x 7.77 cm \\ (10.00 in x 7.50 in x 3.06 in) || | ^ Enclosure | 25.40 cm x 19.05 cm x 7.77 cm \\ (10.00 in x 7.50 in x 3.06 in) || | ||
^ Weight | 2.05 kg (4 lb 8.3 oz) || | ^ Weight | 2.05 kg (4 lb 8.3 oz) || | ||
- | ^ Security | + | ^ Security |
- | --- | + | |
+ | ---- | ||
**Note:** If the device needs to be cleaned, wipe with a dry towel. | **Note:** If the device needs to be cleaned, wipe with a dry towel. | ||
Line 377: | Line 355: | ||
**Note:** Use the ADP5250 in a horizontal orientation. Allow at least 10.16 cm (4.0 in.) of clearance in front and behind the ADP5250 for USB, power, and common connector cabling. | **Note:** Use the ADP5250 in a horizontal orientation. Allow at least 10.16 cm (4.0 in.) of clearance in front and behind the ADP5250 for USB, power, and common connector cabling. | ||
- | ==== Safety Voltages ==== | + | ===== Safety Voltages |
Connect only voltages that are within these limits. | Connect only voltages that are within these limits. | ||
- | === DMM Isolation Voltages (Ground to Earth) === | + | ==== DMM Isolation Voltages (Ground to Earth) |
- | |<100% 25%> | + | |
+ | <columns 100% 5% 95%> | ||
+ | {{: | ||
+ | < | ||
+ | **Hazardous Voltage:** This icon denotes a warning advising you to take precautions to avoid electrical shock. | ||
+ | </ | ||
+ | |||
+ | === Channel-to-earth Ground | ||
+ | |<100% 25%>| | ||
^ Continuous | 300 V, Measurement Category II || | ^ Continuous | 300 V, Measurement Category II || | ||
^ Withstand | 3000 V (RMS), verified by a 5 s dielectric withstand test || | ^ Withstand | 3000 V (RMS), verified by a 5 s dielectric withstand test || | ||
- | --- | + | |
+ | ---- | ||
Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, | Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, | ||
- | === DC Power Supply Isolation Voltages === | + | <columns |
- | |< | + | {{:test-and-measurement: |
- | ^ +25V and -25V to earth ground, continuous | 60VDC, Measurement Category 1 ||| | + | < |
- | --- | + | **Caution: |
+ | </ | ||
- | ====Environmental==== | + | ==== DC Power Supply Isolation Voltages |
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ +25V and -25V to earth ground, continuous | 60 VDC, Measurement Category 1 ||| | |
- | ^ Operating | + | |
- | ^ Storage | + | **Note:** // |
- | ^ Operating | + | |
- | ^ Storage | + | ---- |
+ | =====Environmental===== | ||
+ | |<100% 25%> | ||
+ | ^ Operating | ||
+ | ^ Storage | ||
+ | ^ Operating | ||
+ | ^ Storage | ||
^ Cooling | Forced air circulation (positive pressurization) through a fan. Fan speed automatically adjusts according to operating conditions. Intake and exhaust locations are on rear of device. Ensure that the intake and exhaust locations are not obstructed. || | ^ Cooling | Forced air circulation (positive pressurization) through a fan. Fan speed automatically adjusts according to operating conditions. Intake and exhaust locations are on rear of device. Ensure that the intake and exhaust locations are not obstructed. || | ||
^ Pollution Degree | 2 || | ^ Pollution Degree | 2 || | ||
- | ^ Maximum | + | ^ Maximum |
**Note:** For indoor use only. | **Note:** For indoor use only. | ||
Line 409: | Line 403: | ||
==== Shock and Vibration ==== | ==== Shock and Vibration ==== | ||
- | |<100% 25%> | + | |<100% 25%>| |
- | + | ^ Operational | |
- | ^ Operational | + | ^ Random |
- | ^ Random | + | ^ Random |
- | ^ Random | + | |
- | + | ||
- | --- | + | |
- | + | ||
- | ==== Safety ==== | + | |
- | This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, | + | |
- | * IEC 61010-1, EN 61010-1 | + | |
- | * UL 61010-1, CSA 61010-1 | + | |
- | + | ||
- | --- | + | |
- | + | ||
- | ==== Electromagnetic Compatibility ==== | + | |
- | + | ||
- | This product meets the requirements of the following EMC standards for electrical equipment for measurement, | + | |
- | * EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity | + | |
- | * EN 55011 (CISPR 11): Group 1, Class A emissions | + | |
- | * EN 55022 (CISPR 22): Class A emissions | + | |
- | * EN 55024 (CISPR 24): Immunity | + | |
- | * AS/NZS CISPR 11: Group 1, Class A emissions | + | |
- | * AS/NZS CISPR 22: Class A emissions | + | |
- | * FCC 47 CFR Part 15B: Class A emissions | + | |
- | * ICES-001: Class A emissions | + | |
- | + | ||
- | **Note:** In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, | + | |
- | + | ||
- | **Note:** Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/ | + | |
- | + | ||
- | **Note:** For EMC declarations and certifications, | + | |
- | + | ||
- | + | ||
- | --- | + | |
- | + | ||
- | ====CE Compliance==== | + | |
- | This product meets the essential requirements of applicable European Directives, as follows: | + | |
- | * 2014/35/EU; Low-Voltage Directive (safety) | + | |
- | * 2014/30/EU; Electromagnetic Compatibility Directive (EMC) | + | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
+ | ---- | ||
+ | {{page> | ||
+ | ---- | ||
+ | All specifications provided courtesy of NI's documentation for the VB-8012: https:// |