Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | |||
test-and-measurement:analog-discovery-pro-3x50:getting-started-guide [2022/10/05 15:43] – changed 'Scopes and Instruments' to 'Test and Measurement' Fausto Soares | test-and-measurement:analog-discovery-pro-3x50:getting-started-guide [2023/10/18 19:14] (current) – Alyssa Holzer | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Analog Discovery Pro (ADP3450/ | ||
+ | ~~TechArticle~~ | ||
+ | {{ reference: | ||
+ | ===== Overview ===== | ||
+ | This guide will get you started with your new Analog Discovery Pro, from getting it out of the box to taking your first measurement in the default Standard mode. | ||
+ | ---- | ||
+ | ===== Inventory ===== | ||
+ | * Your new Analog Discovery Pro, along with the included power supply and USB cable. | ||
+ | * BNC oscilloscope probes and BNC to minigrabber clip cables | ||
+ | * A computer, with the WaveForms application (version 3.15.22 or later) installed. | ||
+ | * Installation instructions can be found in Step 2 of this guide. | ||
+ | * Installers for each supported operating system (Windows, Mac, and Linux) can be found here: [[https:// | ||
+ | |||
+ | ---- | ||
+ | ===== Guide ===== | ||
+ | ==== 1. Unboxing ==== | ||
+ | --> | ||
+ | <WRAP group> | ||
+ | <WRAP half column> | ||
+ | The Analog Discovery Pro arrives in a large box. | ||
+ | </ | ||
+ | |||
+ | <WRAP half column> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP half column> | ||
+ | A thin layer of foam and a small walk-around sheet are located on top of the Analog Discovery Pro which is contained in an anti-static bag. | ||
+ | </ | ||
+ | |||
+ | <WRAP half column> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP half column> | ||
+ | Underneath the Analog Discovery Pro, which is nestled in its own tray, are two compartments: | ||
+ | </ | ||
+ | |||
+ | <WRAP half column> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <-- | ||
+ | |||
+ | ---- | ||
+ | ==== 2. Download and Install WaveForms ==== | ||
+ | |||
+ | Digilent' | ||
+ | |||
+ | Check the [[# | ||
+ | |||
+ | Click on the appropriate option below for OS-specific installation instructions. | ||
+ | ---- | ||
+ | |||
+ | --> Installing WaveForms : Windows # | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === Welcome === | ||
+ | First launch the WaveForms installer, by clicking on it in the Downloads folder. Upon launching the WaveForms installer, the welcome page will be seen. Click **Next**. | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === License Agreement === | ||
+ | Read the license agreement on this screen, then, if in agreement to it, click **I Agree** to continue. | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === Choose Components === | ||
+ | In the " | ||
+ | * The Adept Runtime allows WaveForms to communicate with the Analog Discovery 2, Analog Discovery, Analog Discovery Studio, Analog Discovery Pro (ADP3450/ | ||
+ | * The WaveForms Runtime contains a library and device support files needed to run custom applications. | ||
+ | * The WaveForms Application is the Digilent virtual instrumentation interface. | ||
+ | * The Waveforms SDK is the software development kit for creating custom applications. | ||
+ | |||
+ | **Note:** //Even with all components selected, the WaveForms install does not take much hard drive space (< | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === Shortcut Options === | ||
+ | Click **Next**. | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === Choose Install Location === | ||
+ | Click **Install**. | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === Installing / Installation Complete === | ||
+ | Wait for the Installation to complete, then click **Next**. | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | === Complete === | ||
+ | Click **Finish** to close the installer. | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | {{ reference: | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <-- | ||
+ | |||
+ | --> Installing WaveForms : Mac # | ||
+ | |||
+ | <WRAP group>< | ||
+ | From the downloads folder, open the downloaded **.dmg** file. | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | From the desktop, open the **WaveForms** drive. | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | Drag the **WaveForms** icon into the **Applications** folder. | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | The OS may block the launch of WaveForms when it is opened for the first time. If this is the case, go into the System Preferences' | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | |||
+ | <-- | ||
+ | |||
+ | --> Installing WaveForms : Linux # | ||
+ | |||
+ | <WRAP group> | ||
+ | First, download the package for the [[software: | ||
+ | |||
+ | For systems using .deb packages, (Ubuntu, Fedora, etc), use the built-in package manager to install the Adept Runtime and then WaveForms - typically, a package manager can be opened by double-clicking on the file in question. Alternatively, | ||
+ | |||
+ | < | ||
+ | sudo dpkg -i <path to Adept Runtime .deb file> | ||
+ | sudo dpkg -i <path to WaveForms .deb file> | ||
+ | sudo apt-get install -f | ||
+ | </ | ||
+ | |||
+ | For systems using .rpm packages, (Red Hat Linux, etc), use the following set of commands in the terminal to install the Adept Runtime and WaveForms from the downloaded packages: | ||
+ | |||
+ | < | ||
+ | sudo rpm -i <path to Adept Runtime .rpm file> | ||
+ | sudo rpm -i <path to WaveForms .rpm file> | ||
+ | </ | ||
+ | |||
+ | If WaveForms has already been installed on the system, replace the " | ||
+ | |||
+ | For technical support with installing WaveForms on various Linux distributions, | ||
+ | |||
+ | </ | ||
+ | |||
+ | <-- | ||
+ | |||
+ | /*--> Installing WaveForms : Raspberry Pi # | ||
+ | <WRAP group> | ||
+ | {{section> | ||
+ | </ | ||
+ | <--*/ | ||
+ | |||
+ | ---- | ||
+ | ==== 3. Update the Firmware (Optional) ==== | ||
+ | |||
+ | --> In Standard Mode # | ||
+ | <WRAP group> | ||
+ | <WRAP group>< | ||
+ | Plug the Analog Discovery Pro’s power supply into an outlet, then plug the power supply into the Analog Discovery Pro. | ||
+ | |||
+ | Plug the Analog Discovery Pro into the computer via the USB cable. | ||
+ | |||
+ | Flip the Analog Discovery Pro power switch to the on position, on the left side of the unit. The green “power good” indicator LED on the front of the device (far left side) will turn on. | ||
+ | </ | ||
+ | /*{{ : | ||
+ | {{ reference: | ||
+ | /*{{ : | ||
+ | </ | ||
+ | |||
+ | {{page> | ||
+ | </ | ||
+ | <-- | ||
+ | |||
+ | ---- | ||
+ | ==== 4. Take a Measurement ==== | ||
+ | |||
+ | {{ reference: | ||
+ | |||
+ | This section walks through using the Analog Discovery Pro (ADP3450/ | ||
+ | |||
+ | --> Take a Measurement # | ||
+ | |||
+ | <WRAP group>< | ||
+ | === 1. === | ||
+ | If you haven' | ||
+ | === 2. === | ||
+ | Plug the Analog Discovery Pro into the computer via the USB cable. | ||
+ | === 3. === | ||
+ | Flip the Analog Discovery Pro power switch to the on position, on the left side of the unit. The green “power good” indicator LED on the front of the device (far left side) will turn on. | ||
+ | </ | ||
+ | /*{{ : | ||
+ | {{ reference: | ||
+ | /*{{ : | ||
+ | </ | ||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | === 4. === | ||
+ | Take a BNC oscilloscope probe and connect it to the Analog Discovery Pro’s Oscilloscope Channel 1. Connect a BNC to minigrabber clip cable to Wavegen Out Channel 1. Connect the tips together. Set the scope probe' | ||
+ | </ | ||
+ | {{ reference/ | ||
+ | </ | ||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | === 5. === | ||
+ | Launch the WaveForms application. Upon launch, WaveForms will automatically detect and connect to the Analog Discovery Pro in the Device Manager. If the Analog Discovery Pro is not connected to the host computer when WaveForms launches, plug in the device and turn it on, at which point it will appear in the Device Manager’s device list. | ||
+ | |||
+ | If your device doesn' | ||
+ | |||
+ | If an **Update Device** button is visible after selecting the device, __[[test-and-measurement: | ||
+ | After updating the firmware, select the Device and then click **Select** to continue. | ||
+ | |||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | == 6. == | ||
+ | In WaveForms, open the //Wavegen// instrument by clicking on the **Wavegen** button in the instrument panel on the left side of the screen. | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | <WRAP group>< | ||
+ | == 7. == | ||
+ | Leave all settings as defaults, and then go back to WaveForms' | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | ---- | ||
+ | <WRAP group>< | ||
+ | == 8. == | ||
+ | |||
+ | Click the green play arrow in the top right of WaveForms to run all Instruments and begin capturing data. | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | |||
+ | <WRAP group>< | ||
+ | == 9. == | ||
+ | You have now taken your first measurement! | ||
+ | </ | ||
+ | {{ reference: | ||
+ | </ | ||
+ | |||
+ | <-- | ||
+ | ---- | ||
+ | ===== Other Resources ===== | ||
+ | If you want to check out using the device in Linux mode, see [[linux-mode]]. | ||
+ | |||
+ | For more information on streaming data through ethernet while using Standard mode, see [[ethernet-streaming]]. | ||
+ | |||
+ | To find reference materials and guides on how to use the Analog Discovery Pro and WaveForms, please visit the [[start|Analog Discovery Pro (ADP3450/ | ||
+ | |||
+ | For detailed steps about how to install and use WaveForms on Raspberry Pi, follow this guide: [[test-and-measurement: | ||
+ | |||
+ | For technical support, please visit the Test and Measurement section of the [[https:// | ||
+ | |||
+ | ---- |