Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
programmable-logic:usb104a7:zmodadc [2021/09/29 20:27] – Arthur Brownprogrammable-logic:usb104a7:zmodadc [2022/09/12 19:34] – changed forum.digilentinc.com to forum.digilent.com Jeffrey
Line 1: Line 1:
-====== USB104 A7 Zmod Scope 1410  Demo ====== 
-{{ :reference:programmable-logic:usb104a7:adcdemosetup.jpg?direct&800 |}} 
-===== Overview ===== 
-This project demonstrates the implementation of a Zmod Scope 1410 on the USB104 A7. 
  
----- 
-===== Description ===== 
- 
-The simplified block diagram of the system implemented for this demo is shown below: 
-{{ :reference:programmable-logic:usb104a7:usb104a7_ZmodADC_demo.jpg?direct |}} 
- 
-A console application is used to communicate with the USB104 A7. A typical application would be to arm the Zmod Scope 1410 with a specified trigger and store the resulting waveform to a file. The process of an arm operation on channel 1 is as follows: 
- 
-1. Run application and program device. 
- 
-2. Send a trigger level command to device using the application. "level 1.0" 
-  * Triggerlevel opcode (4) or'ed with channel 1 (1<<16) is sent over DPTI, followed by the value 
- 
-3. Send an arm command to device along with a file name to save to. "arm waveform.csv" 
-  * Arm opcode (1) or'ed with channel 1 (1<<16) is sent over DPTI. 
-  * The application then requests a buffer of default length 0x3FFF from the DPTI device. It will wait until data is received before continuing. 
- 
-4. When the trigger occurs data is acquired from the Zmod Scope 1410 and sent to the channelbuffer through DMA. 
- 
-5. Channelbuffer is then sent to the PC application over DPTI and saved to the specified CSV file. 
- 
-The IPs instantiated in the design and their functionality are described below: 
-  * ZmodADC1410 Low Level Controller - initializes the Zmod Scope 1410 hardware and formats the input data according to the AD9648 ADC requirements.   
-  * AXI_ZmodADC - An AXI interface to communicate with the ZmodADC Low Level Controller from a software environment. Sends data to the ZmodADC through DMA. 
-  * AXI_DPTI - Initializes the DPTI interface. Sends and receives data from the DPTI interface through DMA. 
-  * AXI_IIC - An I2C interface to communicate with the ZmodADC hardware. 
-  * AXI_UARTLITE - A UART interface used to send debugging messages to a COM port on the PC. 
- 
-===== Inventory===== 
- 
-===Hardware=== 
-  * [[start|USB104 A7]] 
-    * Including a **USB A cable** and **5V Power Supply** 
-    * NOTE: SW1 DDR voltage set to 1.5V 
-  * [[https://digilent.com/shop/zmod-scope-1410-2-channel-14-bit-oscilloscope-module/|Zmod Scope 1410]] 
-  * [[https://digilent.com/shop/analog-discovery-2-100ms-s-usb-oscilloscope-logic-analyzer-and-variable-power-supply/|Analog Discovery 2 (AD2)]] 
-    * Including a **Micro USB cable** 
-  * [[https://digilent.com/shop/sma-to-alligator-clip-cable/|SMA to Alligator Clip Cable]] 
- 
-===Software=== 
-  * **Vivado Design Suite 2019.1** with **Digilent Board Support Files** installed 
-    * Follow the [[vivado:installing-vivado:start]] guide on how to install Vivado and Digilent Board Support Files. 
-  * [[software/waveforms/waveforms-3/start|Waveforms Software]] 
-  * [[software/adept/start|Digilent Adept Runtime 2.20 or later installed]] 
-  * [[https://ttssh2.osdn.jp/index.html.en|Tera Term]] 
-    * Used to read debug messages from the FPGA. Follow the [[programmable-logic:guides:serial-terminals:start|Serial Terminal Emulator Guide]] for more information on installing and using Tera Term. 
- 
-===Skills=== 
-  * **Basic familiarity with Vivado** 
-    *  //This experience can be found by walking through our "[[vivado/getting_started/2018.2|Getting Started with Vivado]]" guide// 
-  * **Basic familiarity with Digilent Waveforms** 
- 
-===== Downloads ===== 
-|Vivado Project Repository |[[https://github.com/Digilent/USB104A7-ZmodADC|GIT Repo]]| 
-|Vivado Project Repository |[[https://github.com/Digilent/USB104A7-ZmodADC/releases|Releases]]| 
- 
------- 
-===== Demo Setup ===== 
- 
-==== Hardware Setup ==== 
- 
-1. Connect the Analog Discovery 2 board to the host computer using a MicroUSB cable. 
- 
-2. Connect the Zmod Scope 1410 to the USB104 A7 Syzygy port. 
- 
-3. Connect the 5V power supply to the USB104A7. Plug the USB104 A7 into the PC using the USB A cable. 
- 
-4. Screw the SMA to alligator clip cable into the Zmod Scope 1410, channel 1. 
- 
-5. Connect the AD2 to the alligator clips as follows: 
-  * W1 to channel 1 red clip. 
-  * GND to channel 1 black clip. 
- 
-==== Software Setup ==== 
- 
-=== Programming the FPGA === 
- 
-1. Download the release from the git repo [[https://github.com/Digilent/USB104A7-ZmodADC/releases|releases]]. This includes the DPTI Console Application, the Vivado project, and the Xilinx SDK files with the prebuilt output products from Vivado. 
- 
-NOTE: A precompiled bit+elf bit file has been included within the release/FPGA folder. This can be programmed to the FPGA using vivado hardware manager or Digilent Adept. Steps 2 through 8 can be skipped. 
- 
-2. Launch Xilinx SDK. Select the <release directory>/FPGA/sdk_workspace folder as the workspace. 
- 
-3. Click **File>Open Projects from File System**. Click Directory and select the <release directory>/FPGA/sdk_workspace. 
- 
-4. Select **USB104A7_ZmodADC_Demo**, **USB104A7_ZmodADC_Demo_bsp**, and **design_1_wrapper_hw_platform_0**. Click **Finish**. Xilinx SDK will import these projects and build them automatically. 
- 
-5. Program the FPGA by clicking **Xilinx>Program FPGA**. Click **Program**. 
- 
-6. To receive debug messages, open Tera Term and connect to the COM port associated with the USB104A7. Set the baud rate to 115200. 
- 
-7. Program the Microblaze processor with the elf file. In the Project Explorer view, select the **USB104A7_ZmodADC_Demo** project. Click **Run>Run (Ctrl+F11)**. 
- 
-8. Click **Launch on Hardware (System Debugger)** and then click **OK**. 
- 
-=== Generating a waveform === 
- 
-1. Open Digilent Waveforms and select the Wavegen. 
- 
-2. Select the type of waveform to generate and click **Run**. 
- 
----- 
-===== Operating the Demo ===== 
- 
-1. Run <release directory>/DPTI_App/DPTITransferWaveform/USB104A7_ZmodADCDemoApp.exe (USB104A7_ZmodADCDemoApp.o on Linux). The application will start up and connect to the USB104A7's DPTI port. 
- 
-2. Type "level 0.5" to set the trigger level to 0.5V. The Tera Term window should show debug information like in the picture below. 
-{{ :reference:programmable-logic:usb104a7:adc_app.png?direct&600 |}} 
- 
-3. Type "arm waveform.csv" to arm the Zmod Scope 1410. The program will arm the Zmod Scope 1410 and wait until the trigger occurs. 
- 
-4. When the trigger occurs, the device will send the data to the PC and it will be saved to the waveform.csv file. 
-{{ :reference:programmable-logic:usb104a7:adc_app_armed.png?direct&600 |}} 
- 
----- 
-===== Final Notes ===== 
- 
-For more guides and example projects for your USB104 A7, please visit its [[programmable-logic:usb104a7:start|Resource Center]]. 
- 
-For more information about how to use the other Digilent products featured in this demo, please visit their respective Resource Centers: \\ [[test-and-measurement:analog-discovery-2:start]], [[zmod:zmodadc:start]]. 
- 
-For technical support, please visit the [[https://forum.digilentinc.com|Digilent Forums]]. 
- 
-{{tag>learn programmable-logic project usb104a7 zmodadc zmodscope1410}}