Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
programmable-logic:arty-z7:start [2022/04/08 20:08] – [Additional Resources] Arthur Brownprogrammable-logic:arty-z7:start [2023/08/29 23:06] (current) – ↷ Links adapted because of a move operation Arthur Brown
Line 5: Line 5:
 | Store Page = https://digilent.com/shop/arty-z7-zynq-7000-soc-development-board/ | Store Page = https://digilent.com/shop/arty-z7-zynq-7000-soc-development-board/
 | Manual = [[reference-manual]] | Manual = [[reference-manual]]
-| Support = https://forum.digilentinc.com+| Support = https://forum.digilent.com
 | Title = Arty Z7   | Title = Arty Z7  
 | Subtitle = Zynq for Hobbyists and Makers | Subtitle = Zynq for Hobbyists and Makers
Line 29: Line 29:
 | Ethernet = Gigabit Ethernet PHY | Ethernet = Gigabit Ethernet PHY
 | HDMI = Sink (input) \\ Source (output) | HDMI = Sink (input) \\ Source (output)
-| Audio = PWM driven mono audio output \\ with 3.5mm jack+| Audio = PWM driven mono audio output \\ with 3.5 mm jack
 | Pmod Connectors = 2 | Pmod Connectors = 2
 | Other Connectors = Arduino/chipKIT shield connector | Other Connectors = Arduino/chipKIT shield connector
Line 36: Line 36:
 | LEDs = 4 LEDs, 2 RGB LEDs | LEDs = 4 LEDs, 2 RGB LEDs
 | Header = Electrical | Header = Electrical
-| Power Inputs = USB \\ 7V-15V External source+| Power Inputs = USB \\ 7 V - 15 V External source
 | Header = Physical | Header = Physical
 | Width = 3.46 in (88 mm) | Width = 3.46 in (88 mm)
Line 48: Line 48:
  ===== Documentation =====  ===== Documentation =====
 {{topic>arty-z7 +doc -legacy -in-work}} {{topic>arty-z7 +doc -legacy -in-work}}
 +
 +  * {{https://files.digilent.com/resources/programmable-logic/arty-z7/arty-z7-d0-sch.PDF|Arty Z7 Revision D.0 Schematic}}
 +  * {{/reference/programmable-logic/arty-z7/arty_z7_sch.pdf|Arty Z7 Revision B.2 Schematic}}
 +
 +  * {{https://files.digilent.com/resources/programmable-logic/documents/RTL8211F_PCN.pdf|Product Change Notice - Ethernet PHY}}
 +  * {{https://files.digilent.com/resources/programmable-logic/documents/W25Q128JV_PCN.pdf|Product Change Notice - Flash Memory}}
 +
 +**Note:** //Xilinx software tools are not available for download in some countries. Prior to purchasing the Arty Z7, please check the supporting software's availability, as it is required for the board's use.//
  
 ---- ----
Line 61: Line 69:
     * Digilent Pmod IPs can be used to control connected Pmods from baremetal software.     * Digilent Pmod IPs can be used to control connected Pmods from baremetal software.
     * It should be noted that not all Pmods are supported and that Pmod IPs are only supported in versions of Vivado 2019.1 and older.     * It should be noted that not all Pmods are supported and that Pmod IPs are only supported in versions of Vivado 2019.1 and older.
 +  * [[programmable-logic/guides/zynq-baremetal-boot]]
 +  * [[programmable-logic:guides:zynq-servers]]
  
 ---- ----
Line 81: Line 91:
   * {{:reference:programmable-logic:arty-z7:arty_z7_dimensions.zip|Arty Z7 Mechanical Drawing }}   * {{:reference:programmable-logic:arty-z7:arty_z7_dimensions.zip|Arty Z7 Mechanical Drawing }}
   * OOB bit file {{ :reference:programmable-logic:arty-z7:boot.zip |}}   * OOB bit file {{ :reference:programmable-logic:arty-z7:boot.zip |}}
 +  * {{https://files.digilent.com/resources/programmable-logic/arty-z7/SoV-Arty-Z7.pdf|Arty Z7 Statement of Volatility}}