Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
reference:pmod:pmodcon3:start [2021/01/21 23:29] – Arthur Brownpmod:pmodcon3:start [2022/09/13 17:52] – changed forum.digilentinc.com to forum.digilent.com Jeffrey
Line 1: Line 1:
-~~NOTOC~~  
-    
-====== Pmod CON3  ====== 
-   
-{{Digilent Infobox 
-| Store Page = http://store.digilentinc.com/pmodcon3-r-c-servo-connectors/ 
-| Manual = [[reference-manual]] 
-| Support = https://forum.digilentinc.com/forum/7-add-on-boards/ 
-| Title = Pmod CON3 
-| Subtitle = R/C Servo Connectors 
-| Header = Features 
-| Bullet = Four standard 3-wire servo motor connectors 
-| Bullet = Easily interface with Digilent system boards 
-| Bullet = Flexible power delivery to servos 
-| Bullet = 6-pin Pmod port with GPIO interface 
-| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 1 
-| Header = Electrical 
-| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]] 
-| Specification Version = 1.2.0 
-| Logic Level = 3.3V 
-| Header = Physical 
-| Width = 1.0 in (2.54 cm) 
-| Length = 0.80 in (2.03 cm) 
-| Header = Design Resources 
-| Fritzing Part = {{pmodcon3.fzpz| }} 
-| Header = Documentation 
-| Reference Manual = {{https://reference.digilentinc.com/reference/pmod/pmodcon3/reference-manual| }} 
-| Schematic = {{pmodcon3_sch.pdf| }} 
-| Header = J1 Pinout 
-| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}} 
-| Pin 1 = P1 
-| Pin 2 = P2 
-| Pin 3 = P3 
-| Pin 4 = P4 
-| Pin 5 = GND 
-| Pin 6 = VCC 
-}} 
  
-{{page>reference-manual}} \\ \\ 
-  
-===== Tutorials ===== 
-{{topic>pmodcon3 +tutorial}} 
-{{topic>pmod +tutorial}} 
- 
----- 
- 
-===== Example Projects ===== 
-{{topic>pmodcon3 +project}} 
-== Microprocessor== 
-  * {{https://reference.digilentinc.com/learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino}} 
- 
-== Programmable Logic== 
-  * {{:reference:pmod:pmodcon3:pmodcon3_demo.zip|VHDL Example}} 
-  * [[http://www.instructables.com/id/Line-Following-SRK-Robot-with-3d-printed-parts/|Line Following SRK Robot with 3D printed parts]] - Community Project 
-  * [[http://www.instructables.com/id/Using-the-PmodCON3-with-chipKIT-products/|Using the PmodCON3 with chipKIT products]] - Community Project 
-  * [[http://www.instructables.com/id/Controlling-Servos-via-Bluetooth-RN-42-and-LabVIEW/|Controlling Servos via Bluetooth (RN-42) and LabVIEW]] - Community Project 
-{{topic>programmable-logic +pmod }} 
- 
-==Reference Projects== 
-  * {{:reference:pmod:pmodcon3:pmodcon3_refproj.zip|Reference Design}} 
-  * {{:reference:pmod:pmodcon3:pmodcon3_refcomp.zip|Reference Component Design}} 
-  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware/|Setting Up the Zybot - Hardware]] - Community Project 
-  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware-Round-and-Tall-Editi/|Setting up the Zybot - Hardware Round and Tall Edition]] - Community Project 
-  * [[http://www.instructables.com/id/Controlling-Servos-on-FPGA/|Controlling Servos on FPGA]] - Community Project 
- 
----- 
- 
-===== Additional Resources ===== 
-{{topic>pmodcon3 +user-guide}} 
-  * Specification Version 1.2.0: {{https://reference.digilentinc.com/_media/reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}} 
- 
----- 
- 
-{{tag>pmod pmod-start pmod-gpio pmodcon3 servo motors resource-center}}