Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
learn:programmable-logic:tutorials:basys-3-getting-started-with-microblaze:start [2016/08/16 18:38] – jon peyronlearn:programmable-logic:tutorials:basys-3-getting-started-with-microblaze:start [2017/10/20 21:29] (current) – Arthur Brown
Line 1: Line 1:
  
 ====== Basys 3 Getting started in Microblaze  ====== ====== Basys 3 Getting started in Microblaze  ======
 +
 +<WRAP round important 660px>
 +=== Important! ===
 +This guide is obsolete, the updated guide can be found [[:vivado:getting-started-with-ipi:start|here]].
 +</WRAP>
  
 >{{:basys3:abacus_multiply.jpg?600|}} >{{:basys3:abacus_multiply.jpg?600|}}
Line 134: Line 139:
 {{:basys3:image_8.1.jpg?600|}} {{:basys3:image_8.1.jpg?600|}}
  
->4.3) Change default settings in the block options as shown below and click **OK**. This will customize the block with our new user settings.+>4.3) Change default settings in the block options as shown below and click **OK**. This will customize the block with our new user settings.  
 +> 
 +>Local Memory: 128KB 
 +>Local Memory ECC: None 
 +>Cache Configuration: None 
 +>Debug Module: Debug only 
 +>Peripheral AXI Port: Enabled 
 +>Interrupt Controller: unchecked 
 +>Clock Connection: /clk_wiz0/clk_out1(100 MHZ)
 > >
 >{{:basys3:image_1.1.jpg?600|}} >{{:basys3:image_1.1.jpg?600|}}
Line 158: Line 171:
 >{{:basys3:image_12.1.jpg?600|}} >{{:basys3:image_12.1.jpg?600|}}
  
->5.4) Select {{:genesys2:validate.jpg?nolink|}} **Validate Design**. This will check for design and connection errors. There will be an error with the reset of the clock wizard and the rst_clk_wiz.+>5.4) Select {{:genesys2:validate.jpg?nolink|}} **Validate Design**. This will check for design and connection errors. 
 > >
 > >
 >5.5) Click the {{:genesys2:regenerate.jpg?nolink|}} **Regenerate Layout** button to rearrange your block design. The block design should look like >5.5) Click the {{:genesys2:regenerate.jpg?nolink|}} **Regenerate Layout** button to rearrange your block design. The block design should look like
 > >
->{{:learn:programmable-logic:tutorials:basys-3-getting-started-with-microblaze:gsmb_basys3.jpg?600|}}+>{{:learn:programmable-logic:tutorials:basys-3-getting-started-with-microblaze:gsmb_basys3.jpg?800|}}
 > >
->5.9) Select {{:genesys2:validate.jpg?nolink|}} **Validate Design**. This will check for design and connection errors.+>5.6) Select {{:genesys2:validate.jpg?nolink|}} **Validate Design**. This will check for design and connection errors.
 > >
 >{{:basys3:image_14.1.jpg?600|}} >{{:basys3:image_14.1.jpg?600|}}
Line 264: Line 277:
  
 ----- -----
-{{tag>learn programmable-logic tutorial basys-3}}+/*{{tag>learn programmable-logic tutorial basys-3}}*/