Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | |||
learn:instrumentation:tutorials:openscope-mz:getting-started [2022/09/08 15:41] – changed forum.digilentinc.com to forum.digilent.com Jeffrey | learn:instrumentation:tutorials:openscope-mz:getting-started [2023/10/18 19:30] (current) – Alyssa Holzer | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Getting Started with the OpenScope MZ ====== | ||
+ | <WRAP center round important 80%> | ||
+ | Despite our hopes and effort to create an innovative and low-cost T&M solution, we’ve received consistent negative feedback on the OpenScope MZ and OpenLogger regarding overall reliability that has led us to determine that it is not up to our high standards for our test and measurement products. | ||
+ | |||
+ | Unfortunately, | ||
+ | |||
+ | The materials on this page will remain here as legacy sources. Any Digilent provided support for this material will be extremely limited at best. Thank you for understanding. | ||
+ | </ | ||
+ | |||
+ | This document will walk you through the OpenScope MZ setup process. | ||
+ | |||
+ | -->Setup the Digilent Agent and Connect to the OpenScope MZ(Required)# | ||
+ | |||
+ | {{ youtube> | ||
+ | |||
+ | The [[software: | ||
+ | |||
+ | - **Download and install the Digilent Agent**. | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | /* | ||
+ | * [[https:// | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | */ | ||
+ | |||
+ | WaveForms Live provides a browser-based instrumentation environment for managing devices and acquiring data. WaveForms Live uses the Digilent Agent to communicate with local devices via USB. | ||
+ | |||
+ | - Connect the OpenScope MZ to the computer via USB. | ||
+ | * It may take the several seconds for the computer to recognize the device the first time it is connected. | ||
+ | - Right click the Digilent Agent in the system tray and click **Launch WaveForms Live**. | ||
+ | * This will launch waveformslive.com if you have internet access or a locally hosted version of WaveForms Live if not. | ||
+ | - Add the Digilent Agent and OpenScope MZ to WaveForms Live. \\ \\ | ||
+ | * Click **Add A Device**. \\ \\ {{ reference: | ||
+ | * Choose **Agent**. \\ \\ {{ reference: | ||
+ | * Enter the **hostname or IP address** of the device where the Agent is running and click **Add Device**. \\ Typically the default value " | ||
+ | * Select the COM port associated with the OpenScope MZ from the drop down. \\ \\ {{ reference: | ||
+ | |||
+ | <-- | ||
+ | |||
+ | --> | ||
+ | |||
+ | {{ youtube> | ||
+ | |||
+ | \\ \\ | ||
+ | |||
+ | * Click **Update Firmware** and follow the instructions to update the firmware on the OpenScope MZ. \\ \\ {{ reference: | ||
+ | * Review the **Current Firmware Version** on the device and the **Latest Firmware Version** available. | ||
+ | * Select the desired **Available Firmware Version** | ||
+ | * Click **Update**. | ||
+ | * The firmware update should take about 10 seconds and Waveforms Live reports the firmware update progress. | ||
+ | * Click **Done**. | ||
+ | |||
+ | <-- | ||
+ | |||
+ | |||
+ | --> | ||
+ | |||
+ | {{ youtube> | ||
+ | |||
+ | \\ \\ | ||
+ | |||
+ | - Under the **Calibration** section click **Calibrate**. \\ \\ {{ reference: | ||
+ | - Device specific instructions are provided. | ||
+ | - Connect the solid red wire to the solid orange wire. | ||
+ | - Connect the solid white wire to the solid blue wire. | ||
+ | - Click **Next** to begin calibration. | ||
+ | - The calibration process takes about 30 seconds. | ||
+ | - The calibration information is displayed. | ||
+ | - The new calibration data has been applied to the instrument and will be applied at boot. | ||
+ | |||
+ | <-- | ||
+ | |||
+ | |||
+ | -->Take A Measurement (Recommended)# | ||
+ | |||
+ | - Click the new **device card** to navigate to the instrument panel for the OpenScope MZ. \\ \\ {{ : | ||
+ | - Connect the solid orange wire (Osc Ch 1) to solid yellow wire (AWG Ch 1). \\ \\ | ||
+ | - Click the power button to turn on the WaveGen. | ||
+ | - Click Single to acquire a single buffer of data. \\ \\ {{ reference: | ||
+ | - The data is displayed on the chart. | ||
+ | |||
+ | <-- | ||
+ | |||
+ | |||
+ | ==== Related Links ==== | ||
+ | |||
+ | * [[software: | ||
+ | * [[/ | ||
+ | * [[software: | ||
+ | * [[software: | ||
+ | * [[test-and-measurement: | ||
+ | * [[software: | ||
+ | * [[software: | ||
+ | |||
+ | {{tag> | ||
+ | {{include_n> |