Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
learn:instrumentation:tutorials:analog-discovery-studio-protocol-analyzer [2019/06/20 21:15] – [2. Using the Protocol Analyzer] Andrew Holzer | learn:instrumentation:tutorials:analog-discovery-studio-protocol-analyzer [2019/08/21 22:23] (current) – removed Andrew Holzer | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ======Using the Protocol Analyzer (Under Construction)====== | ||
- | {{: | ||
- | |||
- | ===== Introduction ===== | ||
- | This guide explains the use of the // | ||
- | ---- | ||
- | ===== Prerequisites ===== | ||
- | * A Digilent Test & Measurement Device with Digital Input/ | ||
- | * A Computer with WaveForms Software Installed | ||
- | |||
- | ==== 1. Opening the Protocol Analyzer ==== | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | |||
- | === 1.1 === | ||
- | Plug in the Test & Measurement Device, then start WaveForms and make sure the device is connected. | ||
- | |||
- | If no device is connected to the host computer when WaveForms launches, the **Device Manager** will be launched. Make sure that the device is plugged in and turned on, at which point it will appear in the Device Manager' | ||
- | |||
- | **Note:** //" | ||
- | |||
- | **Note:** //The Device Manager can be opened by clicking on the " | ||
- | |||
- | </ | ||
- | <WRAP column half> | ||
- | |||
- | {{ : | ||
- | |||
- | </ | ||
- | </ | ||
- | |||
- | ---- | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | |||
- | === 1.2 === | ||
- | Once the Welcome page loads, in the instrument panel at the left side of the window, click on the **Protocol** button to open the //Protocol Analyzer// instrument. | ||
- | |||
- | </ | ||
- | <WRAP column half> | ||
- | |||
- | {{ : | ||
- | |||
- | </ | ||
- | </ | ||
- | |||
- | ---- | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | |||
- | === 1.3 === | ||
- | Once the //Protocol Analyzer// instrument opens, the window contains the spy panel (1.) showing captured data, the configuration panel (2.) above the spy panel, and the control toolbar (3.) at the top of the window. | ||
- | |||
- | </ | ||
- | <WRAP column half> | ||
- | |||
- | {{ : | ||
- | |||
- | </ | ||
- | </ | ||
- | |||
- | ---- | ||
- | |||
- | ==== 2. Using the Protocol Analyzer ==== | ||
- | |||
- | === 2.1 Hardware Setup === | ||
- | |||
- | This step describes setting up a simple loopback circuit that connects the Test & Measurement device' | ||
- | |||
- | Connect the Test & Measurement devices DIO channel 0 pin (first solid pink wire) to the devices DIO channel 1 pin (first solid green wire). | ||
- | |||
- | === 2.2 === | ||
- | |||
- | === 2.3 === | ||
- | |||
- | === 2.4 === | ||
- | ==== 3. Protocol Analyzer User Interface Overview ==== | ||
- | |||
- | ---- | ||
- | {{tag> |