Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
reference:test-and-measurement:analog-discovery-studio:getting-started-guide [2021/05/07 19:30] – Arthur Brown | test-and-measurement:analog-discovery-studio:getting-started-guide [2022/10/05 16:03] – changed 'Scopes and Instruments' to 'Test and Measurement' Fausto Soares | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Analog Discovery Studio - Getting Started Guide ====== | ||
- | {{ reference: | ||
- | |||
- | ==== Unboxing ==== | ||
- | |||
- | <WRAP group>< | ||
- | The Analog Discovery Studio comes in a sturdy cardboard box. Lift the flap in the front to open the box. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | In the cardboard box, an insert with instructions on getting started with the Analog Discovery Studio and a walkaround of it's features can be found. Keep the insert for reference, or recycle it. Lift the cardboard section containing the Analog Discovery Studio to reveal the MTE cables, power supply and USB cable. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | A foam protector is placed underneath the Breadboard Canvas to protect the power access pins during shipping. Remove the canvas by lifting it straight up to remove the foam. Place the canvas back down onto the Analog Discovery Studio once the foam has been removed. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | The each of the items in the following list comes in the box: | ||
- | * Analog Discovery Studio with Breadboard Canvas | ||
- | * 15V Power Supply Cable with barrel connector for powering the Analog Discovery Studio | ||
- | * USB A to B cable intended to connect the Analog Discovery Studio to a host computer | ||
- | * Sets of MTE cables intended to connect the breadboard to the following sets of pins: | ||
- | * Scope Channel 1 | ||
- | * Scope Channel 2 | ||
- | * Wavegen Channel 1 | ||
- | * Wavegen Channel 2 | ||
- | * Digital I/O | ||
- | * Power Access | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | |||
- | |||
- | ---- | ||
- | ==== Download and Install WaveForms ==== | ||
- | |||
- | {{ reference: | ||
- | |||
- | |||
- | Digilent' | ||
- | |||
- | If WaveForms is already installed, please make sure that it is up to date (version 3.10.9 or later). | ||
- | ---- | ||
- | |||
- | --> Installing WaveForms : Windows # | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === Welcome === | ||
- | First launch the WaveForms installer, by clicking on it in the Downloads folder. Upon launching the WaveForms installer, the welcome page will be seen. Click **Next**. | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === License Agreement === | ||
- | Read the license agreement on this screen, then, if in agreement to it, click **I Agree** to continue. | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === Choose Components === | ||
- | In the " | ||
- | * The Adept Runtime allows WaveForms to communicate with the Analog Discovery 2, Analog Discovery, Analog Discovery Studio, Digital Discovery, and Electronics Explorer Board. | ||
- | * The WaveForms Runtime contains a library and device support files needed to run custom applications. | ||
- | * The WaveForms Application is the Digilent virtual instrumentation interface. | ||
- | * The Waveforms SDK is the software development kit for creating custom applications. | ||
- | |||
- | **Note:** //Even with all components selected, the WaveForms install does not take much hard drive space (< | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === Shortcut Options === | ||
- | Click **Next**. | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === Choose Install Location === | ||
- | Click **Install**. | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === Installing / Installation Complete === | ||
- | Wait for the Installation to complete, then click **Next**. | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <WRAP group> | ||
- | <WRAP column half> | ||
- | === Complete === | ||
- | **Finish**. | ||
- | </ | ||
- | <WRAP column half> | ||
- | {{ reference: | ||
- | </ | ||
- | </ | ||
- | |||
- | <-- | ||
- | |||
- | --> Installing WaveForms : Mac # | ||
- | |||
- | <WRAP group>< | ||
- | From the downloads folder, open the downloaded **.dmg** file. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | From the desktop, open the **WaveForms** drive. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | Drag the **WaveForms** icon into the **Applications** folder. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | |||
- | --> Install Drivers : Only for OS-X 10.13 or earlier # | ||
- | |||
- | **Skip this section if the OS version is newer than OS-X 10.13.** | ||
- | |||
- | /*For OS-X 10.14 Mojave or later, if the Digilent FTDI Driver is installed, the device may not be detected. Please see the **Troubleshooting** section of the [[https:// | ||
- | |||
- | ---- | ||
- | <WRAP group>< | ||
- | === Launch Installer === | ||
- | Double click **DigilentFtdiDriver.pkg** to open the FTDI Driver Installer. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | The OS may block the launch of the driver installer. If this is the case, go into the System Preferences' | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === Introduction === | ||
- | Click **Continue**. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === Read Me === | ||
- | Click **Continue**. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === License === | ||
- | Read the license, then if in agreement, click **Continue**, | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === Destination Select === | ||
- | Pick the users to install the drivers for, then click **Continue**. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === Installation Type === | ||
- | Click **Install**. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === Summary === | ||
- | Once the installation has completed, click **Close**. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | |||
- | <-- | ||
- | |||
- | ---- | ||
- | <WRAP group>< | ||
- | The OS may block the launch of WaveForms when it is opened for the first time. If this is the case, go into the System Preferences' | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | |||
- | <-- | ||
- | |||
- | --> Installing WaveForms : Linux # | ||
- | |||
- | <WRAP group> | ||
- | First, download the package for the [[reference: | ||
- | |||
- | For systems using .deb packages, (Ubuntu, Fedora, etc), use the built-in package manager to install the Adept Runtime and then WaveForms - typically, a package manager can be opened by double-clicking on the file in question. Alternatively, | ||
- | |||
- | < | ||
- | sudo dpkg -i <path to Adept Runtime .deb file> | ||
- | sudo dpkg -i <path to WaveForms .deb file> | ||
- | sudo apt-get install -f | ||
- | </ | ||
- | |||
- | For systems using .rpm packages, (Red Hat Linux, etc), use the following set of commands in the terminal to install the Adept Runtime and WaveForms from the downloaded packages: | ||
- | |||
- | < | ||
- | sudo rpm -i <path to Adept Runtime .rpm file> | ||
- | sudo rpm -i <path to WaveForms .rpm file> | ||
- | </ | ||
- | |||
- | If WaveForms has already been installed on the system, replace the " | ||
- | |||
- | For technical support with installing WaveForms on various Linux distributions, | ||
- | |||
- | </ | ||
- | |||
- | <-- | ||
- | |||
- | /*--> Installing WaveForms : Raspberry Pi # | ||
- | <WRAP group> | ||
- | {{section> | ||
- | </ | ||
- | <--*/ | ||
- | |||
- | ---- | ||
- | |||
- | ==== Take a Measurement ==== | ||
- | |||
- | {{ reference: | ||
- | |||
- | This section walks through using the Analog Discovery Studio for the first time. An analog output pin is connected to an analog input pin, and a waveform is generated and captured via this simple loopback circuit. | ||
- | |||
- | --> Take a Measurement # | ||
- | |||
- | <WRAP group>< | ||
- | === 1. === | ||
- | Plug in the Analog Discovery Studio' | ||
- | ---- | ||
- | === 2. === | ||
- | Plug in the Analog Discovery Studio to the computer via the USB cable. | ||
- | ---- | ||
- | === 3. === | ||
- | Flip the Analog Discovery Studio' | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | == 4. == | ||
- | Take out the two sets of MTE cables for the Analog Discovery Studio' | ||
- | |||
- | Connect the black wire (GND) of the wavegen MTE cable to the white-striped wire (1-) of the scope MTE cable by plugging each of them into the same row of the breadboard. | ||
- | |||
- | On a different row of the breadboard, do the same for the yellow wire (W1) of the wavegen MTE cable and the solid orange wire (1+) of the scope | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | === 5. === | ||
- | Launch WaveForms. Upon launch, WaveForms will automatically detect and connect to the Analog Discovery Studio. | ||
- | If the Analog Discovery Studio is not connected to the host computer when WaveForms launches, the Device Manager will be launched. Make sure that the device is plugged in and turned on, at which point it will appear in the Device Manager' | ||
- | |||
- | **Note:** // | ||
- | |||
- | **Note:** //The Device Manager can be opened by clicking on the “Connected Device” button in the bottom right corner of the screen (3), or by selecting “Device Manager” from the “Settings” menu at the top of the screen.// | ||
- | </ | ||
- | {{ : | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | == 6. == | ||
- | In WaveForms, open the " | ||
- | </ | ||
- | {{ learn: | ||
- | </ | ||
- | <WRAP group>< | ||
- | Leave all settings as defaults, and click the green arrow at the top of the window to play the wave. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | ---- | ||
- | <WRAP group>< | ||
- | == 7. == | ||
- | Go back to WaveForms' | ||
- | </ | ||
- | {{ learn: | ||
- | </ | ||
- | <WRAP group>< | ||
- | Leave all settings as defaults and click the green play arrow to begin capturing data. | ||
- | </ | ||
- | {{ reference: | ||
- | </ | ||
- | |||
- | <-- | ||
- | |||
- | |||
- | ---- | ||
- | ==== Next Steps ==== | ||
- | |||
- | /* For FIXME, visit the **Analog Discovery Studio** website. FIXME link */ | ||
- | |||
- | To find reference materials and guides on how to use the Analog Discovery Studio and WaveForms, please visit the [[start|Analog Discovery Studio Resource Center]]. | ||
- | |||
- | For detailed steps about how to install and use WaveForms on Raspberry Pi, follow this guide: [[reference: | ||
- | |||
- | For technical support, please visit the Scopes and Instruments section of [[https:// | ||
- | |||
- | ---- | ||
- | {{tag> |