Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
test-and-measurement:analog-discovery-studio:canvases:fpga-board-adapter-canvas:getting-started [2024/03/22 22:11] – removed - external edit (Unknown date) 127.0.0.1 | test-and-measurement:analog-discovery-studio:canvases:fpga-board-adapter-canvas:getting-started [2024/04/03 17:06] (current) – [Introduction] updated number of LEDs to six Fausto Soares | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Getting Started with the FPGA Board Adapter Canvas ====== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ===== Introduction ===== | ||
+ | This guide explains the use of the FPGA Board Adapter Canvas with the Analog Discovery Studio. The FPGA Board Adapter Canvas is used to host one of our FPGA boards and user-designed circuitry. | ||
+ | |||
+ | * One 300 tie-point solderless breadboard | ||
+ | * One 50 tie-point power rail | ||
+ | * Six power supply indication LEDs | ||
+ | * One 24 tie-point breadboard power supplies contact points | ||
+ | | ||
+ | |||
+ | ---- | ||
+ | |||
+ | =====Inventory===== | ||
+ | |||
+ | * FPGA Board Adapter Canvas | ||
+ | * Note: The FPGA Board Adapter Canvas was formerly known as the Interposer Canvas, and the original product name is reflected on the printed circuit board | ||
+ | * USB Cable to connect to FPGA board | ||
+ | * 4 standoffs for mounting the FPGA board above the FPGA Board Adapter Canvas | ||
+ | * 8 screws for mounting the FGA Board and standoffs to the FPGA Board Adapter Canvas | ||
+ | |||
+ | ---- | ||
+ | |||
+ | =====Demonstration===== | ||
+ | |||
+ | ==== 1. Setup ==== | ||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | == 1.1 == | ||
+ | The FPGA Board Adapter Canvas is an optional accessory for the Analog Discovery Studio. The FPGA Board Adapter Canvas is attached to the Analog Discovery Studio through magnets beneath each of the four standoffs in the corners. To begin setting up install the four black standoffs in the designated location for your FPGA board. | ||
+ | |||
+ | </ | ||
+ | <WRAP column half> | ||
+ | |||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | ---- | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | == 1.2 == | ||
+ | Plug the included USB cable into the USB type A slot on the FPGA Board Adapter Canvas. | ||
+ | |||
+ | </ | ||
+ | <WRAP column half> | ||
+ | |||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | == 1.3 == | ||
+ | With the remaining 4 screws, attach the FPGA board to the standoffs you screwed into place on the FPGA Board Adapter Canvas. | ||
+ | |||
+ | </ | ||
+ | <WRAP column half> | ||
+ | |||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | == 1.4 == | ||
+ | |||
+ | Plug the micro USB plug into the FGA board. | ||
+ | |||
+ | </ | ||
+ | <WRAP column half> | ||
+ | |||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | == 1.5 == | ||
+ | Unplug your Analog Discovery Studio board from both the USB and power connectors. | ||
+ | |||
+ | <WRAP center round important 60%> | ||
+ | Ensure that the Analog Discovery Studio is turned OFF before installing the FPGA Board Adapter Canvas board. | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | <WRAP column half> | ||
+ | |||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | ==== 2. Out of the Box Demo Mode ==== | ||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | == 2.1 == | ||
+ | Each compatible FPGA board comes with an " | ||
+ | |||
+ | </ | ||
+ | <WRAP column half> | ||
+ | |||
+ | {{: | ||
+ | </ | ||
+ | </ | ||
+ | ---- | ||
+ | ===== Next Steps ===== | ||
+ | |||
+ | For more guides on how to use your Analog Discovery Studio device, check out its resource center: [[test-and-measurement: | ||
+ | |||
+ | To find more information on the FPGA Board Adapter canvas, and for links to the resource centers for the various compatible FPGA development boards, check out the FPGA Board Adapter Canvas' | ||
+ | |||
+ | For more information on WaveForms, visit the [[software: | ||
+ | |||
+ | For technical support, please visit the [[https:// | ||
+ | |||
+ | {{tag> | ||