Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
learn:instrumentation:tutorials:analog-discovery-studio-spectrum-analyzer [2019/05/31 21:24] – Ian Etheridge | learn:instrumentation:tutorials:analog-discovery-studio-spectrum-analyzer [2023/02/13 22:36] (current) – Arthur Brown | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ======Using the Spectrum Analyzer====== | + | ======Using the Spectrum Analyzer (Redirect) ====== |
- | This guide walks through the process of setting up WaveForms' | + | ~~REDIRECT>test-and-measurement: |
- | + | ~~NOSEMANTIC~~ | |
- | ==== 1. Opening the Scope ==== | + | {{tag>redirect}} |
- | + | ||
- | <WRAP group> | + | |
- | <WRAP column half> | + | |
- | == 1.1 == | + | |
- | Plug in your <test & measurement device>, then start WaveForms and make sure your device is connected. | + | |
- | + | ||
- | If no device is connected to the host computer when WaveForms launches, the **Device Manager** will launch automatically. | + | |
- | + | ||
- | Make sure that the device is plugged in and turned on, at which point it will appear in the Device Manager' | + | |
- | + | ||
- | **Note:** //The Device Manager can be reopened by clicking on the " | + | |
- | </ | + | |
- | <WRAP column half> | + | |
- | </ | + | |
- | </ | + | |
- | ---- | + | |
- | <WRAP group> | + | |
- | <WRAP column half> | + | |
- | == 1.2 == | + | |
- | Once the Welcome page loads, in the **Instrument Panel** at the left side of the window, click on the **Spectrum** button to open the // | + | |
- | </ | + | |
- | <WRAP column half> | + | |
- | </ | + | |
- | </ | + | |
- | ---- | + | |
- | <WRAP group> | + | |
- | <WRAP column half> | + | |
- | == 1.3 == | + | |
- | Once the // | + | |
- | </WRAP> | + | |
- | <WRAP column half> | + | |
- | </ | + | |
- | </ | + | |
- | + | ||
- | ---- | + | |
- | ==== 2. Using the Spectrum Analyzer==== | + | |
- | + | ||
- | //This section walks through setting up the Spectrum Analyzer tool to analyze the frequency response of a simple signal.// | + | |
- | <WRAP group> | + | |
- | <WRAP column half> | + | |
- | == 2.1 Hardware Setup == | + | |
- | In order to measure a signal with the //Spectrum // instrument, there must first be a signal to measure. To this end, step 2.1 of this guide describes setting up a simple loopback circuit that connects the <test & measurement | + | |
- | + | ||
- | Connect the <test & measurement device>' | + | |
- | </ | + | |
- | <WRAP column half> | + | |
- | </ | + | |
- | </ | + | |
- | ---- | + | |
- | == 2.2 Input Signal == | + | |
- | With the loopback circuit set up, a signal must now be applied to the analog output pins. WaveForms' | + | |
- | + | ||
- | From the // | + | |
- | + | ||
- | For more detail on how to use the //Wavegen// instrument, please see the [[learn:instrumentation:tutorials: | + | |
- | + | ||
- | Return to the // | + | |
- | </ | + | |
- | <WRAP column half> | + | |
- | </ | + | |
- | </ | + | |
- | ---- | + | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | {{tag>tutorial analog-discovery-studio}} | + |