FMC Pcam Adapter Reference Manual
The FMC Pcam Adapter is an FMC mezzanine (peripheral) board allowing interfacing up to four Pcam camera modules to field-programmable gate array (FPGA) based systems. It extends the capabilities of development platforms to enable multi-camera video applications.
- Four Pcam system-side connectors
- Level translators from MIPI D-PHY to LVDS and LVCMOS
- Male FMC LPC connector for digital signals
- Compatible with a wide range of VADJ voltages (1.8V – 3.3V)
Modified March 31, 2020 - Removed Dual load variant, which was never sold.
Created April 9, 2019
This manual applies to REV C.0 of the board.
Carrier Card Compatibility
As with any FMC mezzanine module, there are some compatibility requirements. These must be evaluated before connecting and powering the module.
- Supported VADJ voltage range is 1.8 V - 3.3 V. The voltage is controlled by the carrier card.
- The carrier card must be capable of providing enough current. See Power Supplies.
- Must use I/O standards compatible with the voltage levels of the digital outputs, and the chosen VADJ. For example, LVDS_25 and LVCMOS25 with a VADJ of 2.5V.
- Receiver signal termination for outputs is the responsibility of the carrier card. For example, DIFF_TERM can be used for LVDS_25 and a VADJ of 2.5V.
- The carrier card might have either the low-pin count or the high-pin count FMC female connector. However, not all pins are required to be wired. Compare the carrier card FMC pin-out against the pin-out from chapter 1.4 below.
FPGA I/O Architecture Compatibility
Receiving several independent source-synchronous high-speed interfaces in the FPGA is no easy feat due to I/O and clocking restrictions specific to the FPGA architecture. The VITA 57.1 specs are not granular enough for the requirements of today's high-speed I/O architectures. Therefore, not all carrier cards will be able to support all ports of the FMC Pcam Adapter simultaneously. Some of the requirements are:
- Clock inputs are mapped to LA00, LA01, LA17, and LA18. Verify that the carrier board maps these to clock-capable input pins.
- Each clock has two data lanes associated with it. Verify that the clock signal can be routed to I/O primitives sampling the data lanes. On some architectures the clock and its data lanes must be mapped to the same bank.
- Two ports are mapped to LA00-LA16, and the other two mapped to LA17-LA33. Usually, carrier cards split these groups into separate banks. Therefore, each bank must support two ports at once. This puts a considerable constraint on the resources available in each bank. Clock buffers, PLLs and high-speed de-serialization primitives must be capable of receiving two independent D-PHY interfaces. The UltraScale architecture in particular has a very restrictive clock/strobe propagation mechanism. The side-effect of propagation is that some pins are made unavailable for other purposes including other Pcam ports. This might include pins unrelated to FMC, but mapped to the FMC bank.
Digilent recommends implementing an RTL design with the desired number of D-PHY interfaces constrained to the pinout of the carrier card to be used for development before committing to the FMC Pcam Adapter.
The table below lists carrier cards confirmed compatible by Digilent. Boards not listed can still be compatible, if the requirements above are met. Check back for updates as the list will be extended.
|Carrier Card||Manufacturer||FMC Port||VADJ||Simultaneous Pcam Port Usage|
|ZedBoard||Digilent||J1 (LPC)||2.5 V||✔||✔||✔||✔|
Table 1. Confirmed compatibility matrix.
1. Functional Description
The adapter board's main purpose is to translate the MIPI D-PHY input to LVDS/LVCMOS outputs that are supported on most FPGAs. It also translates the 3.3V control signals of the Pcam to the adjustable I/O voltage powering the FMC bank, VADJ. Therefore, compatibility is extended to boards with FPGAs that have only low-voltage I/O banks (<= 1.8V).
1.1. Pcam ports
The Pcam ports are system-side, 15-pin, bottom-load, top-contact FFC connectors. Pcam modules are connected using the flexible-foil cable provided with them. The correct cable orientation is with the contact pads facing away from the board. Please see Figure 2 below for details.
Ports are designated with letters from A to D. All signals have the letter designator in their name. It is also written on the silkscreen of the PCB.
Ports C and D were designed to channel the cable through cut-outs on the board so that four Pcam modules can be accommodated.
1.2. Level translators
There are two types of level translators onboard: for control signals and for MIPI D-PHY inputs. Both translate between voltage levels of the FMC bank supplied by VADJ and a second power domain.
1.2.1. Control signals
Control signals are driven by SN74AVC4T245 or SN74AVC2T245, which are 4-bit or 2-bit dual-supply voltage level translation devices. The A-side pins are supported by VCCA, and the B-side are supported by VCCB. Starting from the logic diagram shown underneath, a high on DIR allows data transmission from side A to side B. Similarly, a low on DIR and OE# allows data transmission from side B to side A. When OE# is set to high, both sides are isolated, and all their pins are in the high-impedance state. Figure 3. Logic Diagram for SN74AVC4T245
Some control signals are uni-directional, so the DIR and OE# of their level translators are hard-wired to always-on. These are: CAM[A-D]_BTA, CAM_PWUP, LP[A-D]_LANE1_[PN]_LS, and LP[A-D]_CLK_[PN]_LS.
Other control signals are bi-directional, so their DIR and OE# are available to the user. These are CAM[A-D]_GPIO1 and LP[A-D]_LANE0_[PN]_LS.
GPIO1 signals from all four ports are controlled as a group using common CAM_GPIO1_OEN and CAM_GPIO1_DIR. The GPIO1 signals are connected to the camera ports (one per port). On Pcam 5C they are unused, but on other cameras they may have some extra functionality.
|CONTROL INPUTS||OUTPUT CIRCUITS||OPERATION|
|CAM_GPIO1_OEN#||CAM_GPIO1_DIR||A Side||B Side|
|L||L||Enabled||Hi-Z||From FMC to Pcam|
|L||H||Hi-Z||Enabled||From Pcam to FMC|
Table 1. Summary of Communication Modes
LP[A-D]_LANE0_[PN]_LS signals support per-port direction reversal using CAM[A-D]_BTA. This functionality is described in chapter 1.6 below.
1.2.1. MIPI D-PHY inputs
The conversion of MIPI D-PHY input streams into LVDS high-speed and CMOS low-power is made with the MC20901 IC from Meticom. This requires an understanding of lane states and is done automatically by the level translator. It separates the superimposed low-power and high-speed voltage levels into dedicated signals easier to interpret by the FPGA input buffers.
Table 2. MIPI D-PHY level translation
1.3. Voltage levels of output signals
The high-speed outputs are compliant with Xilinx LVDS_25 and LVDS standards. These standards have a typical input common-mode voltage of 1.2V for 100Ω transmission lines. It is important to mention that for LVDS high-speed lines, 100Ω differential termination is needed at the receiver, on the carrier board. The Xilinx LVDS_25 and LVDS standards offer the possibility of enabling differential termination internal to the FPGA (using DIFF_TERM = TRUE constraint); for this the constraint file has to be modified accordingly. If the carrier board has external differential termination on these lines, the DIFF_TERM constraint is not needed.
The low-power signals are compliant with the LVCMOS standard corresponding to the selected VADJ voltage level.
The DC characteristics for the high-speed outputs of the MC20901 IC are listed in the table below.
|VCM-OUT||Output common mode voltage||VDD=1.2V||1.09||1.2||1.31||V|
|VDO-Diff||Differential output voltage||250||300||350||mVp|
Table 3. High-Speed Outputs (HS-X-P, HS-X-N)
|FMC Pin||MIPI Function||FMC Pin||MIPI Function|
Table 4. Pin Mapping
1.5. I2C Switch
All the cameras are configured using I2C. As all the cameras have identical I2C addresses, a 4-port I2C switch (TCA9546A) is used to connect the master SCL/SDA signal pair to all the cameras, one switch channel corresponding to one camera. It is important to mention that the master can select each individual switch channel as well as any combination of the four channels, SC0/SD0-SC3/SD3.
The power-on state of the switch is with the channels disabled. Therefore, before any communication with the Pcam ports can take place the corresponding channel must be enabled.
In order to configure the I2C switch, the master must send a start condition via I2C followed by the switch address. The switch address is selectable through GA0 and GA1 FMC connector pins. The switch address is 8 bits long and starts with “11100” followed by the logic values on the GA0 and GA1 pins, respectively. The last bit is reserved to define the operation to be performed. Logic 1 is the equivalent for read and 0 for write. After a successful acknowledgment of an address by the switch, the I2C master device sends a byte to the switch, which is then stored in its control register. This control register enables or disables each individual channel. Logic 1 on bits 0-3 in the control register enable channels SC0/SD0 - SC3/SD3. Conversely, logic 0 will disable the channel.
Once the switch is configured to enable the desired channel(s), a new start condition can be generated by the I2C master, after which it can output on his I2C bus the address of the camera with whom it is trying to communicate.
1.6. Low-Power Reverse Communication/Bus turn-around (BTA)
Normally MIPI CSI-2 lanes are unidirectional, input to the module. Support for bidirectional lanes and low-power reverse escape mode is provided on lane 0 of each Pcam port only. Control signals CAM[A-D]_BTA decide the direction of communication. Logic low is the normal use case, where the Pcam module is transmitting and the FMC Pcam Adapter forwards data to the FPGA. A logic high will reverse data flow and low-power signals from the FPGA will be forwarded to the Pcam module. A 4.7 Kohm pull-down on CAM[A-D]_BTA is provided on-board.
High-Speed Reverse Communication is not supported.
|Low||from Pcam to FMC||from Pcam to FMC|
|High||N/A||from FMC to Pcam|
Table 5. Summary of Communication Modes
1.7. Power supplies
The adapter board is powered from three power rails available in the FMC connector.
|Power rail||Powered circuits||Maximum current consumption [mA]|
|3P3VAUX||IPMI FRU EEPROM, I2C multiplexer||20||20|
|3P3V||LDOs, Pcam VCC3V3, level translators||1000||500|
Table 6. Loads on FMC Power Rails
Two LDOs provide additional voltages for the level translators. Power rails VCC2V5 and VCC1V2 are used internally only and not provided to any external circuit.
|Power rail||Powered circuits||Max current consumption [mA]|
Table 7. Loads on Internal Power Rails
1.8. FMC Support
The FMC Pcam Adapter uses a Samtec ASP-134604-01 low pin-count male connector as the main connector for digital signals. The board fully conforms to the VITA 57.1 specs. The connector supports the full range of 1.8V-3.3V bank supply voltages (VADJ). Check compatibility requirements above.
I²C serves as the IPMI EEPROM, providing hardware definition information. For more information, consult the VITA 57.1 specs.