~~NOTOC~~ 
     
====== Pmod ACL2 ======
   
{{Digilent Infobox
| Store Page = https://digilent.com/shop/pmod-acl2-3-axis-mems-accelerometer/
| Manual = [[reference-manual]]
| Support = https://forum.digilent.com/forum/7-add-on-boards/
| Title = Pmod ACL2
| Subtitle = 3-Axis MEMS Accelerometer
| Header = Features
| Bullet = User Selectable Resolution
| Bullet = Less than 2 uA consumption at 100 Hz
| Bullet = Activity and inactivity monitoring
| Bullet = Free fall detection
| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}}
| Header = Key Specifications
| Range = ±2/4/8g
| Resolution = 12-bits
| FIFO Depth = 512 Samples
| Header = Electrical
| Bus = [[learn/fundamentals/communication-protocols/spi/start | SPI]]
| Specification Version = 1.2.0
| Logic Level = 3.3V
| Header = Physical
| Width = 0.95 in (2.41 cm)
| Length = 0.80 in (2.03cm)
| Header = Design Resources
| Fritzing Part = {{reference:pmod:pmodacl2:pmodacl2.fzpz| }}
| Header = Documentation
| Primary IC = [[http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL362.pdf | ADXL362]]
| Reference Manual = [[reference/pmod/pmodacl2/reference-manual]]
| Schematic = {{reference:pmod:pmodacl2:pmodacl2_sch.pdf| }}
| Header = J1 Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-2x6.png?direct |}}
| Pin 1 = ~CS
| Pin 2 = MOSI
| Pin 3 = MISO
| Pin 4 = SCLK
| Pin 5 = GND
| Pin 6 = VCC
| Pin 7 = INT2
| Pin 8 = INT1
| Pin 9 = NC
| Pin 10 = NC
| Pin 11 = GND
| Pin 12 = VCC
| Header = J2 Pinout
| Pin 1 = INT1
| Pin 2 = GND
| Header = J3 Pinout
| Pin 1 = INT2
| Pin 2 = GND
}}

{{page>reference-manual}} \\ \\

---- 

===== Example Projects =====
==Microprocessor==
  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
  * {{:reference:pmod:pmodacl2:pmodacl2-mpide-example.zip| Library and MPIDE Example}}
  * [[http://www.instructables.com/id/Float-a-Ping-Pong-Ball-at-Will/?ALLSTEPS |Float a ping pong ball at will!]] - Community Project
  * [[http://www.instructables.com/id/Raspberry-Pi-Rainbow-Ruler/ |Raspberry Pi Rainbow Ruler]] - Community Project
  * [[https://www.hackster.io/mmigs/using-the-pmod-acl2-with-arduino-uno-ac83fd|Using the Pmod ACL2 with Arduino Uno]] - Application note

==Programmable Logic==
  * Arty A7 100T project using the Pmod ACL2, Pmod CLS, and Pmod 7SD created by user Tim S. on the Digilent Forum [[https://forum.digilent.com/topic/20397-muxssd-driver-for-the-pmod-ssd/|Forum thread]]
  * [[learn/programmable-logic/tutorials/pmod-ips/start | Getting Started with Digilent Pmod IPs]]
     * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier. 

----
===== Additional Resources =====
  * [[https://wiki.analog.com/resources/fpga/xilinx/pmod/adxl362|ZedBoard Demo Project]]
  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}

----

{{tag>pmod pmod-start pmod-spi pmodacl2 accelerometer resource-center}}